Loading ...
Loading ...
Loading ...
– 223 –
Chapter 9 Network Connection — NDI|HX function
[SYSTEM] menu
[NETWORK] menu → [NDI|HX]
[FREQUENCY] [REC FORMAT] [STREAMING FORMAT]
[1080-50.00i/AVC-I200]
[1080-50.00i/AVC-I100]
[1080-50.00i/AVC-I50]
[1080-50.00i/AVC-G50]
[1080-50.00i/AVC-G25]
[1080-50.00i/AVC-G12]
[1080-25.00p/422LongGOP 50M]
[1080-25.00p/422ALL-I 100M]
[1080-50.00i/422LongGOP 50M]
[1080-50.00i/422ALL-I 100M]
[1920×1080-25fps 14M]
[1920×1080-25fps 10M] (Factory setting)
[1920×1080-25fps 6M]
[1280×720-25fps 8M]
[1280×720-25fps 4M]
[1280×720-25fps 2M]
[720-50.00p/AVC-I200]
[720-50.00p/AVC-I100]
[720-50.00p/AVC-I50]
[720-50.00p/AVC-G50]
[720-50.00p/AVC-G25]
[720-50.00p/AVC-G12]
[1280×720-50fps 14M]
[1280×720-50fps 10M] (Factory setting)
[1280×720-50fps 6M]
Enabling the NDI|HX function
Perform the setting for the NDI|HX function, and then enable the NDI|HX function referring to the information in the NewTek website, etc. [NDI|HX] is
displayed in the [NETWORK] menu → [NDI|HX] → [ACTIVATION] when the NDI|HX function is enabled.
@
NOTE
t The NDI|HX function will remain enabled once it has been set, unless the activation information saved on the camera is deleted.
t To enable the NDI|HX function of the camera using the tool from NewTek, it is necessary to select [NDI|HX] in the [NETWORK] menu → [NETWORK
FUNC].
Streaming with multicast
One streaming can be distributed to multiple NDI|HX compatible switchers via supported router, etc., when the multicast function is used.
1
Select the [NETWORK] menu → [NDI|HX] → [MULTICAST] → [ENABLE].
2
Select the [NETWORK] menu → [NDI|HX], and specify [MULTICAST ADDRESS] and [MULTICAST PORT].
f Set [MULTICAST ADDRESS] within following range.
IPv4: 224.0.1.0 to 239.255.255.254
IPv6: Multicast address starting with FF
f Set [MULTICAST PORT] within the range of 1024 to 50000.
@
NOTE
t One that has added +1 to the end of the specied multicast address is also used for NDI|HX.
t Disable the LAN card not to be used when receiving the multicast image to be displayed on a computer with multiple LAN cards installed.
t Range of streaming can be adjusted with the [NETWORK] menu → [STREAMING] → [NDI|HX] → [TTL/HOP LIMIT]. For details, contact the network
administrator.
Using the NDI|HX function
Control the camera by operating the NDI|HX compatible switcher.
@
NOTE
t Streaming may stop when the date/time is set while streaming.
t Take caution as streaming image may unintentionally be released depending on the system environment to stream on and setting of the service and
system used.
Disabling the NDI|HX function
1
Select the [NETWORK] menu → [NDI|HX] → [CLEAR ACTIVATION].
The activation information saved to the camera is deleted.
After the activation information is deleted, the NDI|HX function cannot be used until the NDI|HX function is enabled again.
Loading ...
Loading ...
Loading ...