Loading ...
Loading ...
Loading ...
(147,1)
[ Edit: 2020/ 8/ 19 Model: T32-A ]
NOTE:
Once the button is pressed, you have
approximately 30 seconds to initiate the
next step.
6. Return to the vehicle and firmly press and
hold the programmed HomeLink® button
for two seconds and release. Repeat the
“press/hold/release” sequence up to 3
times to complete the programming pro-
cess. HomeLink® should now activate your
rolling code equipped device.
7. If you have any questions or are having
difficulty programming your HomeLink®
buttons, refer to the HomeLink® web site
at: www.homelink.com.
OPERATING THE HomeLink® UNIVERSAL
TRANSCEIVER
GUID-68441759-7704-47A0-BE37-19F4DFFABB83
The HomeLink® Universal Transceiver, after it is
programmed, can be used to activate the
programmed device. To operate, simply press
and release the appropriate programmed
HomeLink® Universal Transceiver button. The
amber indicator light will illuminate while the
signal is being transmitted.
For convenience, the hand-held transmitter of
the device may also be used at any time.
PROGRAMMING TROUBLESHOOTING
GUID-A6AD2DFC-C4A4-4F60-AE87-75B4679FD409
If the HomeLink® does not quickly learn the
hand-held transmitter information:
. replace the hand-held transmitter batteries
with new batteries.
. position the hand-held transmitter with its
battery area facing away from the
HomeLink® surface.
. press and hold both the HomeLink® and
hand-held transmitter buttons without in-
terruption.
. position the hand-held transmitter 26 to 76
mm (1 to 3 in) away from the HomeLink®
surface. Hold the transmitter in that posi-
tion for up to 15 seconds. If HomeLink® is
not programmed within that time, try
holding the transmitter in another position
- keeping the indicator light in view at all
times.
If you have any questions or are having
difficulty programming your HomeLink® but-
tons, refer to the HomeLink® web site at: www.
homelink.com.
CLEARING THE PROGRAMMED INFOR-
MATION
GUID-08D972A2-A208-4044-ACAD-8B01836AC192
The following procedure clears the pro-
grammed information from both buttons. In-
dividual buttons cannot be cleared. However,
individual buttons can be reprogrammed, see
“Reprogramming a single HomeLink® button”
(P.2-77).
To clear all programming
GUID-3AEA6B1C-6970-4F3D-9E19-D2B4279D6E00
1. Press and hold the two outer HomeLink®
buttons until the indicator light begins to
flash in approximately 10 seconds. Do not
hold for longer than 20 seconds.
2. Release both buttons.
HomeLink® is now in the programming mode
and can be programmed at any time beginning
with “Programming HomeLink®” - Step 1.
REPROGRAMMING A SINGLE HomeLink®
BUTTON
GUID-F98BB3C6-C31D-4655-A19F-8D5E8137BA0B
To reprogram a HomeLink® Universal Transcei-
ver button, complete the following.
1. Press and hold the desired HomeLink®
button. Do not release the button.
2. The indicator light will begin to flash after
20 seconds. Without releasing the
HomeLink® button, proceed with “Program-
ming HomeLink®” - Step 1.
For questions or comments, contact
HomeLink® at: www.homelink.com.
The HomeLink® Universal Transceiver button
has now been reprogrammed. The new device
can be activated by pushing the HomeLink®
button that was just programmed. This proce-
dure will not affect any other programmed
HomeLink® buttons.
IF YOUR VEHICLE IS STOLEN
GUID-E0EEA60A-412E-4342-A1A7-F725E8A1D589
If your vehicle is stolen, you should change the
codes of any non-rolling code device that has
been programmed into HomeLink®. Consult the
Owner’s Manual of each device or call the
manufacturer or dealer of those devices for
additional information.
When your vehicle is recovered, you will need
to reprogram the HomeLink® Universal
Transceiver with your new transmitter infor-
mation.
Instruments and controls 2-77
Condition: 'Except for China'/
Loading ...
Loading ...
Loading ...