Loading ...
Loading ...
Loading ...
Operation—Operator's Station
Continued on next page KR46761,0001154 -19-14DEC16-1/2
Switch Panel Functions
1. Back Button (for monitor use)—Press button to
return to previous menu.
2. Home Button (for monitor use)—Press button to
return to default screen when in any of the monitor menus.
If key switch is in OFF position, press and hold button to
check hour meter and fuel amount on monitor.
3. Monitor Dial (for monitor use)—Press dial to go
from default screen to main menu screen. Rotate dial to
highlight desired menu function on monitor. Press dial to
select desired screen information or to conrm desired
action.
4. Temperature Control/Mode Switch—Press switch to
toggle between different air vent settings. Air conditioner
display on monitor shows different settings each time
switch is pressed. There are four different settings:
•
Air ows out of front vent and defroster vents.
•
Air ows out of front, rear, and defroster vents.
•
Air ows out of front, rear, foot, and defroster vents.
•
Air ows out of foot vents.
Rotate switch counterclockwise for cooler air setting and
clockwise for warmer air setting. Temperature setting
changes on air conditioner display as switch is rotated
either way.
5. Blower Speed Switch—Press switch while air
conditioner is OFF to select AUTO mode (blower speed
setting and air ow setting are selected automatically).
Temperature control/mode switch can be rotated to
operator's preferred cab temperature setting. Blower
speed and air ow settings adjust automatically to reach
and maintain desired cab temperature.
If blower speed switch is rotated or temperature
control/mode switch is pressed while in AUTO mode,
AUTO mode is canceled and all settings need to be
adjusted by operator as needed.
If blower speed switch is pressed while air conditioner is
on, air conditioner turns off. Blower speed switch must be
on to operate on/off function of air conditioner in monitor
menu.
Rotate switch to adjust blower speed to desired setting
when not in AUTO mode.
6. Radio Tuning Switch—Press switch to toggle between
AM and FM frequency. Rotate switch to select desired
radio station.
On machines equipped with the auxiliary input, when
personal device is plugged in, the radio tuning switch will
toggle between AM, FM, and AUX. See Operating the
AM/FM Radio in this section.
7. Radio Power and Volume Switch—Press switch to
turn radio on or off. Rotate switch to adjust volume to
desired setting.
8. Engine Speed Dial—Turn dial clockwise to increase
engine speed or counterclockwise to decrease engine
speed.
9. Auto-Idle Switch—Turn switch to select between A/I
ON or A/I OFF.
With engine on, move auto-idle switch to A/I ON and
engine speed dial to above auto-idle speed. Auto-idle
indicator appears on monitor when auto-idle is on. Engine
runs at engine speed dial setting for 4 seconds and then
auto-idle system slows engine to auto-idle engine speed.
When any pilot control lever is operated, engine speed
increases to engine speed dial setting. When pilot control
levers are placed back in neutral position, auto-idle circuit
automatically slows engine to auto-idle engine speed after
4 seconds.
Turn auto-idle switch to A/I OFF and set engine speed dial
to improve machine control in difcult work areas, loading,
and unloading. Auto-idle indicator disappears on monitor.
10. Travel Mode Switch—Turn switch to select between
fast (rabbit) or slow (turtle) speed travel.
11. Power Mode Button—Press button to select different
engine speed modes:
•
ECO (economy) Mode—use to improve fuel efciency
and reduce noise level with a small difference in engine
speed.
•
PWR (power) Mode—use when general digging work is
needed.
•
H/P (high power) Mode—use when more ow is desired
for booming up or rolling in the arm in excavation work.
12. Work Light Switch—Switch has three positions:
•
First Position—drive light on base of machine turns on.
Switch panel also illuminates.
•
Second Position—drive light on base of machine,
upper cab lights, boom lights, arm lights (if equipped),
and rear cab lights (if equipped) turn on. Switch
panel illuminates and monitor changes to night mode
(background lighting is dimmed).
•
OFF—work lights and switch panel illumination turns off.
13. Windshield Wiper and Washer Switch—Switch has
ve operating positions:
•
OFF—wiper stops operating and is retracted.
•
INT (slow)—wiper operates intermittently at 8-second
intervals.
•
INT (medium)—wiper operates intermittently at
6-second intervals.
•
INT (fast)—wiper operates intermittently at 3-second
intervals.
•
ON—wiper operates continuously.
Push and hold switch to squirt uid on windshield. If
switch is held more than 2 seconds, wiper operates until
switch is released. Do not hold-down switch for more than
20 seconds.
2-1-3
112321
PN=96
Loading ...
Loading ...
Loading ...