Loading ...
Loading ...
Loading ...
WARNING!
•
Do not run your vehicle in a closed garage or con-
fined area while programming the transmitter.
Exhaust gas from your vehicle contains carbon mon-
oxide which is odorless and colorless. Carbon monox-
ide is poiso nou s when inhaled and can cause you
and others to be severely injured or killed.
PROGRAMMING HOMELINK® TO A
MISCELLANEOUS DEVICE
The procedure on how to program HomeLink® to a mis-
cellaneous device follows the same procedure as pro-
gramming to a garage door opener
page 68. Be
sure to determine if the device has a rolling code, or
non-rolling code before beginning the programming
process.
NOTE:
Canadian Radio Frequency (RF) laws require transmi tter
signals to time-out (or quit) after several seconds of tr ans-
mission, which may not be long enough for HomeLink® to
pick up the signal during programming. Similar to this
Canadian law, some U.S. gate ope rators are designed to
time-out in t he same manner. The procedure may need to
be performed multiple times to successfully pair the
device to your HomeLink® buttons.
REPROGRAMMING A SINGLE
HOMELINK® BUTTON
To reprogram a single HomeLink® button that has been
previously trained, without erasing all the channels,
proceed as follows. Be sure to determine whether the
new device you want to program the HomeLink® button
to has a rolling code, or no n-rolling cod e.
1. Place the ignition in the ON/RUN position, without
starting the engine.
2. Push and hold the desired HomeLink® button until
the HomeLink® Ind ica tor light begins to flash after
20 seconds. Do not release the button.
3. Without releasing the button, proceed with Step 2
in “Programming HomeLink® To A Garage Door
Opener” and follow all remai ning steps.
CANADIAN/GATE OPERATOR
PROGRAMMING
For programming transmitters in Canada/United States
that require the transmitter signals to “time-out” after
several seconds of transmission.
Canadian Radio Frequency (RF) laws require transmi tter
signals to time-out (or quit) after several seconds of tr ans-
mission, which may not be long enough for HomeLink® to
pick up the signal during programming. Similar to this
Canadian law, some U.S. gate ope rators are designed to
time-out in t he same manner.
It may be helpful to unplug the device during the cycling
process to prevent possible overheating of the gar age
door or gate motor.
1. Place the ignition in the ON/RUN position.
NOTE:
For vehicles equipped with Keyless Enter ‘n Go™,
place the ignit io n in the RUN position. Make sure
while programming HomeLink® wi th the engine on
that your vehicle is outside of your garage, or that
the garage doo r remains open at all times.
2. Place the hand-held transmitter 1 to 3 inches (3 to
8 cm) away from the HomeLink® button you wish to
program while keeping the HomeLink® indicator
light in view.
3. Continue to push and hold the HomeLink® button
while you push and release (cycle) your hand-held
transmitter every two seconds until HomeLink® has
successfully accepted the frequency signal. The indi-
cator light will flash slowly and then rapidly when
fully trained.
4.
Watch for the HomeLink® indicator to change flash
rates. When it changes, it is programmed. It may take
up to 30 second s or longer in rare cases. The garage
door may open and close while you are programming.
5. Push and hold the programmed HomeLink® button
and observe the indicator light.
NOTE:
○
If the indic ator light stays on constantly, program-
ming is complete and the garage door/device
should activate when the HomeLink® button is
pushed.
○
To program the two remaining HomeLink® but-
tons, repeat each step for each remaining but-
ton. DO NOT erase the channels.
If you unplugged the garage door opener/device for
programming, plug it back in at this time.
Reprogramming A Single HomeLink® Button
(Canadian/Gate Operator)
To reprogram a channel that has been previously
trained, follow these steps:
1. Place the ignition in the ON/RUN position.
2. Press and hold the desired HomeLink® button until
the indicator light begins to flash after 20 seconds.
Do not release the button.
3. Without releasing the button, proceed with
“Canadian/Gate Operator Programming” step 2 and
follow all remaining steps.
GETTING TO KNOW YOUR VEHICLE 69
2
Loading ...
Loading ...
Loading ...