Loading ...
Loading ...
Loading ...
300
Effects
Chorus, Flanger, and Phaser (Cho/Fln Phaser)
28: St.HarmonicChorus
(Stereo Harmonic Chorus)
This effect applies chorus only to higher frequencies. This can be
used to apply a chorus effect to a bass sound without making the
sound thinner. You can also use this chorus block with feedback
as a flanger.
f: High/Low Split Point
This parameter sets the frequency that splits the high and low
range. Only the high range will be sent to the chorus block.
g: Feedback
Sets the feedback amount of the chorus block. Increasing the
feedback will allow you to use the effect as a flanger.
29: St. Biphase Mod.
(Stereo Biphase Modulation)
This stereo chorus effect adds two different LFOs together. You
can set the Frequency and Depth parameters for each LFO indi-
vidually. Depending on the setting of these LFOs, very complex
waveforms will create an analog-type, unstable modulated
sound.
a
LFO Waveform Triangle, Sine Selects the LFO Waveform
LFO Phase
[degree]
–180...+180
Sets the LFO phase difference
between the left and right
b
LFO Frequency
[Hz]
0.02...20.00 Sets the speed of the LFO
Src Off...Tempo
Selects a modulation source for LFO
speed
Amt
–20.00...
+20.00
Sets the modulation amount of LFO
speed
c
MIDI Sync Off, On
When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency
BPM
MIDI,
40.00...
300.00
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Base Note r...w
Selects the type of notes that
specify the LFO speed
Times x1...x32
Sets the number of notes that
specify the LFO speed
d
Pre Delay
[msec]
0.0...50.0
Sets the delay time from the original
sound
e
Depth 0...100 Sets the depth of LFO modulation
Src Off...Tempo
Selects the modulation source of
the LFO modulation depth
Amt –100...+100
Sets the modulation amount of the
LFO modulation depth
f
High/Low Split
Point
1...100
Sets the frequency split point
between the low and high range
g
Feedback –100...+100
Sets the feed back amount of the
chorus block
High Damp [%] 0...100
Sets the high range damping
amount of the chorus block
h
Low Level 0...100 Sets the low range output level
High Level 0...100
Sets the high range (chorus) output
level
i
Wet/Dry
Dry, 1:99...99:1,
Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
Left
Right
Feedback
LFO Phase
LFO: Tri / Sine
FX Amt
FX Amt
High Damp
Stereo In - Stereo Out
Low Level
Low Level
High Level
High Level
High/Low Split Point
High Damp
Chorus/Flanger
Chorus/Flanger
a
LFO1
Waveform
Triangle, Sine Selects LFO1 waveform
LFO2 Triangle, Sine Selects LFO2 waveform
Phase Sw
0 deg,
180 deg
Switches the LFO phase difference
between left and right
b
LFO1
Frequency [Hz]
0.02...30.00 Sets the LFO1 speed
Src Off...Tempo
Selects the modulation source of
LFO1&2 speed
LFO1 Amt
–30.00...
+30.00
Sets the modulation amount of
LFO1 speed
c
LFO2
Frequency [Hz]
0.02...30.00 Sets the LFO2 speed
Amt
–30.00...
+30.00
Sets the modulation amount of
LFO2 speed
d
Depth1 0...100
Sets the depth of LFO1
modulation
Src Off...Tempo
Selects the modulation source of
LFO1&2 modulation depth
Amt –100...+100
Sets the modulation amount of
LFO1 modulation depth
e
Depth2 0...100
Sets the depth of LFO2
modulation
Amt –100...+100
Sets the modulation amount of
LFO2 modulation depth
f
L Pre Delay
[msec]
0.0...50.0
Sets the delay time for the left
channel
R Pre Delay
[msec]
0.0...50.0
Sets the delay time for the right
channel
g
Feedback –100...+100
Sets the feedback amount
High Damp
[%]
0...100
Sets the damping amount in the
high range
h
Wet/Dry
-Wet, -
1:99...Dry...99:1
, Wet
Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 283
Amt –100...+100 Amount of modulation source
Chorus/Flanger
Left
Right
Feedback
180 [degree]
FX Amt
FX Amt
High Damp
Stereo In - Stereo Out
LFO1: Tri / Sine
LFO2: Tri / Sine
Chorus/Flanger
High Damp
LFO1
LFO2
Bi-Phase Modulation LFO
Depth1
Depth2
+
Loading ...
Loading ...
Loading ...