Loading ...
Loading ...
Loading ...
X: Applicable —: Not Exit
Items
MIL DTC 1st trip DTC
1st trip 2nd trip
1st trip
displaying
2nd trip
displaying
1st trip
displaying
2nd trip
displaying
Blinking Lighting up Blinking
Lighting
up
Misfire (Possible three way catalyst
damage) — DTC: P0300 - P0306
is being detected
X — ————X—
Misfire (Possible three way catalyst
damage) — DTC: P0300 - P0306
is being detected
——X——X——
Throttle control motor — DTC:
P1128
—X——X———
Closed loop control
— DTC: P1148, P1168
—X——X———
Fail-safe items (Refer to EC-129.) — X — — X*1 — X*1 —
Except above — — — X — X X —
*1: Except “ECM”
Emission-related Diagnostic Information
NFEC0031
DTC AND 1ST TRIP DTC
NFEC0031S01
The 1st trip DTC (whose number is the same as the DTC number) is displayed for the latest self-diagnostic
result obtained. If the ECM memory was cleared previously, and the 1st trip DTC did not reoccur, the 1st trip
DTC will not be displayed.
If a malfunction is detected during the 1st trip, the 1st trip DTC is stored in the ECM memory. The MIL will not
light up (two trip detection logic). If the same malfunction is not detected in the 2nd trip (meeting the required
driving pattern), the 1st trip DTC is cleared from the ECM memory. If the same malfunction is detected in the
2nd trip, both the 1st trip DTC and DTC are stored in the ECM memory and the MIL lights up. In other words,
the DTC is stored in the ECM memory and the MIL lights up when the same malfunction occurs in two con-
secutive trips. If a 1st trip DTC is stored and a non-diagnostic operation is performed between the 1st and
2nd trips, only the 1st trip DTC will continue to be stored. For malfunctions that blink or light up the MIL dur-
ing the 1st trip, the DTC and 1st trip DTC are stored in the ECM memory.
Procedures for clearing the DTC and the 1st trip DTC from the ECM memory are described in “HOW TO
ERASE EMISSION-RELATED DIAGNOSTIC INFORMATION”, EC-91.
For malfunctions in which 1st trip DTCs are displayed, refer to EC-86. These items are required by legal
regulations to continuously monitor the system/component. In addition, the items monitored non-continuously
are also displayed on CONSULT-II.
1st trip DTC is specified in Mode 7 of SAE J1979. 1st trip DTC detection occurs without lighting up the MIL
and therefore does not warn the driver of a problem. However, 1st trip DTC detection will not prevent the
vehicle from being tested, for example during Inspection/Maintenance (I/M) tests.
When a 1st trip DTC is detected, check, print out or write down and erase (1st trip) DTC and Freeze Frame
data as specified in “Work Flow” procedure Step II, refer to EC-121. Then perform “DTC Confirmation Proce-
dure” or “Overall Function Check” to try to duplicate the problem. If the malfunction is duplicated, the item
requires repair.
How to Read DTC and 1st Trip DTC
NFEC0031S0101
DTC and 1st trip DTC can be read by the following methods.
With CONSULT-II
With GST
CONSULT-II or GST (Generic Scan Tool) Examples: P0117, P0340, P1065, etc.
These DTCs are prescribed by SAE J2012.
(CONSULT-II also displays the malfunctioning component or system.)
NO TOOLS
The number of blinks of the MIL in the Diagnostic Test Mode II (Self-Diagnostic Results) indicates the DTC.
Example: 0117, 0340, 1065, etc.
I 1st trip DTC No. is the same as DTC No.
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
Two Trip Detection Logic (Cont’d)
EC-76
Loading ...
Loading ...
Loading ...