Loading ...
Loading ...
Loading ...
19
The dry time of the hand dryer has increased. Inspect the inlet grille for dust and remove.
Inspect filter and change if required.
Ensure that the hose is securely attached to
the base of the tap and no leaks are present.
Must be performed by a qualified electrician.
Air is continuously running from the
hand dryer.
Ensure sensors are clean and free
from obstructions.
There is no air coming from the hand dryer. Check fuse/circuit breaker is working
and that the power is connected. Must be
performed by a qualified electrician.
Ensure that the air hose is securely
attached to the base of the tap and no
leaks are present. Must be performed by a
qualified electrician.
Check that the sensor cable from the tap is
securely connected. Must be performed by a
qualified electrician.
TAP
Problem Action
Water is continuously coming from the tap. Ensure sensors are clean and free
from obstructions.
There is no water coming from the tap. Ensure that the power and water supplies are
turned on and that the isolation valve is open.
Must be performed by a qualified electrician.
Ensure that the aerator is free from debris,
remove and clean/replace if necessary.
The water coming from the tap is overly hot
or cold.
Contact the Dyson Helpline.
If you have any further questions please contact the Dyson Helpline.
USE IN FOOD PREPARATION AREAS
For food preparation environments special installation is required, which must fully enclose the
motor bucket and hose in a cleanable housing or have the motor bucket on the reverse side of
a wall, provide adequate clearance for cleaning underneath (if applicable) and be such that the
unit is at least 2.5 metres (8.20 feet) from uncovered food or uncovered food-contact surfaces.
CLEANING
The hand dryer should be cleaned daily.
Wipe sensors using a soft cloth and non-abrasive cleaner then place cleaning cap over sensors
to prevent air and water from being activated.
Clean all tap surfaces, sink, mirror and any walls or counter tops. When complete
REMEMBER to remove cleaning cap.
REGULARLY clean air inlets on base of motor bucket (under sink). Ensure plughole in sink is free
from blockages so water can drain freely.
IMPORTANT INFORMATION
Do not pressure wash the appliance.
All cleaning chemicals should be used exactly as indicated by the manufacturer’s
instructions (including appropriate dilution).
If a cleaning product is left on the machine for too long, a film will form. This may reduce the
effectiveness of the antimicrobial surfaces.
Any chemicals intended for use should first be tested on an inconspicuous area to confirm
suitability. Aside from cleaning chemicals, care should be taken to avoid any harmful fluids
from coming into contact with the product, in particular oils and alcohol-based products.
WATER GUIDELINES
This hand dryer has an IP35 certification.
Use of pressure washers can force water inside the casing.
Water damage caused by incorrect cleaning will invalidate your warranty.
AUTOMATIC DUTY FLUSH
The unit is equipped with a fixed automatic water flush, which activates for 60 seconds
24 hours after last use. This helps reduce water stagnation and bacteria proliferation within
the product.
Please ensure the unit is always installed over a functional basin with free and
connected drainage.
SOLENOID REPLACEMENT GUIDELINES
It may be necessary to replace the solenoid on your hand dryer. If you suspect this is the case,
please contact the Dyson Helpline.
When replacing the solenoid, the hand dryer must be disconnected from the mains electricity
and water supply. Failure to do so could lead to serious injury and/or damage to property.
FILTER MAINTENANCE
Regularly check the air inlet to ensure that it is free from dust and debris. Simply wiping the inlet
with a soft cloth should be sufficient to remove dust and debris.
If the air inlet gets clogged, further cleaning or a filter change might be required.
If required for high usage environments, a Dyson filter change kit provides everything needed
to change your unit’s HEPA filter on site. Contact the Dyson Helpline for more information.
Filter cleaning or replacement for your hand dryer can be carried out by carefully following
the instructions given in the filter change kit. If in any doubt, consult a qualified electrician or
contact the Dyson Helpline for support.
SERVICING
If your hand dryer needs servicing, please call the Dyson Helpline. Also visit the website at
www.dysoncanada.ca.
CA
CAFR
27.11.2017 12:51 - C92757_WD04_OPMAN_INT_X588-OWNERS-MANUAL-PART 3- TEXT.indd_15_0c2s_15_0c2s
Loading ...
Loading ...
Loading ...