Loading ...
Loading ...
Loading ...
STARTING AND OPERATING 193
Front Park Assist Audible Alerts
ParkSense will turn off the Front Park Assist audible alert
(chime) after approximately three seconds when an
obstacle has been detected, the vehicle is stationary, and
the brake pedal is applied.
Adjustable Chime Volume Settings
The Front and Rear chime volume settings are
programmable.
The settings may be programmed through the Uconnect
System. Refer to “Uconnect Settings” in “Multimedia” for
further information.
The chime volume settings include low, medium, and high.
The factory default volume setting is medium.
ParkSense will retain its last known configuration state
through ignition cycles.
ENABLING AND DISABLING PARKSENSE
ParkSense can be enabled and disabled with the
ParkSense switch.
When the ParkSense switch is pushed to
disable the system, the instrument cluster
display will show the “PARKSENSE OFF”
message for approximately five seconds. Refer
to “Instrument Cluster Display” in “Getting To Know Your
Instrument Panel” for further information.
When the gear selector is moved to REVERSE and the
system is disabled, the instrument cluster display will
show the “PARKSENSE OFF” message for as long as the
vehicle is in REVERSE.
The ParkSense switch LED will be on when ParkSense is
disabled or requires service. The ParkSense switch LED
will be off when the system is enabled. If the ParkSense
switch is pushed, and the system requires service, the
switch LED will blink momentarily, and then the LED will
be on.
SERVICE THE PARKSENSE PARK ASSIST
S
YSTEM
During vehicle start up, when the ParkSense System has
detected a faulted condition, the instrument cluster will
actuate a single chime, once per ignition cycle, and it will
display the “PARKSENSE UNAVAILABLE WIPE REAR
SENSORS”, “PARKSENSE UNAVAILABLE WIPE FRONT
SENSORS” or “PARKSENSE UNAVAILABLE SERVICE
REQUIRED” message. When the gear selector is moved to
REVERSE and the system has detected a faulted
condition, the instrument cluster display will display a
“PARKSENSE UNAVAILABLE WIPE REAR SENSORS” or
“PARKSENSE UNAVAILABLE SERVICE REQUIRED”
message for as long as the vehicle is in REVERSE. Under
this condition, ParkSense will not operate. Refer to
“Instrument Cluster Display” in “Getting To Know Your
Instrument Panel” for further information.
If “PARKSENSE UNAVAILABLE WIPE REAR SENSORS” or
“PARKSENSE UNAVAILABLE WIPE FRONT SENSORS”
appears in the instrument cluster display make sure the
outer surface and the underside of the rear fascia/
bumper and/or front fascia/bumper is clean and clear of
snow, ice, mud, dirt or other obstruction and then cycle the
ignition. If the message continues to appear, see an
authorized dealer.
If the “PARKSENSE UNAVAILABLE SERVICE REQUIRED”
message appears in the instrument cluster display, see an
authorized dealer.
CLEANING THE PARKSENSE SYSTEM
Clean the ParkSense sensors with water, car wash soap,
and a soft cloth. Do not use rough or hard cloths. In
washing stations, clean sensors quickly keeping the vapor
jet/high pressure washing nozzles at least 4 inches
(10 cm) from the sensors. Do not scratch or poke the
sensors. Otherwise, you could damage the sensors.
PARKSENSE SYSTEM USAGE
P
RECAUTIONS
NOTE:
Ensure that the front and rear bumpers are free of
snow, ice, mud, dirt and debris to keep the ParkSense
system operating properly.
Jackhammers, large trucks, and other vibrations could
affect the performance of ParkSense.
When you turn the ParkSense system off, the instru-
ment cluster display will show a vehicle graphic of the
ParkSense on/off state for two seconds. Furthermore,
once you turn ParkSense off, it remains off until you
turn it on again, even if you cycle the ignition.
When you move the gear selector to the REVERSE posi-
tion and ParkSense is turned off, the instrument
cluster display will show the “ParkSense OFF”
message. This message will be displayed for as long as
the vehicle is in REVERSE.
5
20_JT_OM_EN_USC_t.book Page 193
Loading ...
Loading ...
Loading ...