Loading ...
Loading ...
Loading ...
Operation—Monitor Operation
Continued on next page KR46761,00013E7 -19-02FEB17-1/2
Monitor Functions
1. Auto-Idle Indicator: Displays if auto-idle mode is
turned ON from the switch panel. For more information,
see Switch Panel Functions. (Section 2-1.)
2. Auto-Shutdown Indicator: Displays if auto shutdown
was selected by operator from the menu screen. For
more information, see Main Menu—Setting Menu—Auto
Shutdown in this section.
3. Work Mode Indicator: Displays icon for the current
attachment being used.
4. Travel Speed Indicator: Displays travel speed
selected from the switch panel (rabbit—fast speed travel
or turtle—slow speed travel).
5. Aftertreatment Device Regeneration Indicator:
Displays condition of the aftertreatment device
regeneration. Two different indicators could appear here:
•
Aftertreatment Device Regeneration Indicator
appears when aftertreatment device temperature is
high during an auto or manual regeneration.
NOTE: The aftertreatment device regeneration inhibit
indicator will display on the monitor when
the key switch is in ON position. Once the
engine is started, the indicator will disappear
unless aftertreatment device regeneration
inhibit has been turned off by the operator
through the monitor.
•
Aftertreatment Device Regeneration Inhibit Indicator
appears when aftertreatment device regeneration inhibit
has been enabled by the operator. For more information,
see Main Menu—Setting Menu—Aftertreatment Device
Regeneration Inhibit in this section.
6. Auxiliary Indicator: Displays optional auxiliary data
indicator.
7. Power Mode Indicator: Displays a power mode
selected from the switch panel (ECO, PWR, or H/P). For
more information, see Switch Panel Functions. (Section
2-1.)
8. Auxiliary Indicator: Displays optional auxiliary data
indicator.
9. Auxiliary Indicator: Displays optional auxiliary data
indicator.
10. Reversing Fan Indicator (if equipped): Displays
when reversing cooling fan is activated by reversing fan
switch on left panel.
11. Hour Meter and Clock: Displays total machine
operation hours counted since the machine started
working in the unit of hours (h). One digit after the decimal
point indicates tenths of an hour (6 minutes).
Clock indicates present time.
TX1086447 —UN—05JAN11
Aftertreatment Device
Regeneration Indicator
TX1086347 —UN—06JAN11
Aftertreatment Device
Regeneration Inhibit Indicator
12. Engine Preheat Indicator:
IMPORTANT: Prevent engine damage. Do not
use ether in this machine.
If preheating is required, the engine preheat indicator is
automatically lit. If preheating is not required, this indicator
will not display.
13. Seat Belt Indicator: Displays when key switch is in
ON position, and disappears 5 seconds after the engine
starts.
14. Diesel Exhaust Fluid (DEF) Gauge: Displays
approximate level of diesel exhaust uid (DEF) remaining
in the DEF tank. If diesel exhaust uid (DEF) is low, last
segment of DEF gauge and outer ring illuminates yellow.
When DEF level is severely low, engine power derates
and last segment of DEF gauge illuminates yellow and
blinks. When DEF level is empty, engine power and speed
derates. All segments of DEF gauge are off, outer ring
illuminates red, and warning indicators appear. Engine
can start, but machine cannot be operated until DEF tank
is lled. Fill DEF tank before last segment turns yellow.
15. Fuel Gauge: Displays remaining fuel amount as
indicated by the needle. Fuel machine before needle
reaches E.
16. Fuel Mark: If fuel sensor is malfunctioning, color of
the fuel mark changes and the needle disappears. If the
harness between the fuel sensor and the monitor unit is
broken, the needle disappears but the fuel mark color
does not change.
17. Sub Meter: Displays fuel consumption or breaker
hours depending on what is set in the monitor. For more
information, see Main Menu—Setting Menu—Sub Meter
Selection in this section.
18. Coolant Temperature Gauge:
IMPORTANT: Possible engine damage may occur. If
needle points to RED zone, idle engine to bring
back to BLUE zone before stopping engine. If
needle continues to rise, stop engine.
Displays engine coolant temperature. Needle should be
around the center of the scale during operation.
2-2-2
112321
PN=125
Loading ...
Loading ...
Loading ...