Loading ...
Loading ...
Loading ...
English - 12 -
Media Browser Menu(depending on the model)
You can play photo, music and movie ¿les stored
on a USB disk by connecting it to your TV. Connect
a USB disk to one of the USB inputs located on the
side of the TV. Pressing the Menu button while in
the Media Browser mode will access the Picture,
Sound and Settings menu options. Pressing the
Menu button again will exit from this screen.
You
can set your Media Browser preferences by using
the Settings Menu.
/oop/ShufÀe Mode Operation
Start playback with the Play
button and activate
All ¿les in the list will be
continuously played in original
order
Start playback with the OK
button and activate
The same ¿le will be played
continuously (repeat)
Start playback with the Play
button and activate
All ¿les in the list will be
played once in random order
Start playback with the Play
button and activate
,
All ¿les in the list will be
continuously played in the
same random order.
Recording a Programme
IMPORTANT: When using a new USB hard disk drive,
it is recommended that you ¿rst format the disk using
your TV’s “Format Disk” option.
To record a programme, you should ¿rst connect a
USB disk to your TV while the TV is switched off. You
should then switch on the TV to enable the recording
feature.
To use recording your USB drive should have 2 GB
free space and be USB 2.0 compatible. If the USB
drive is not compatible an error message will be
displayed.
To record long duration programmes such as movies,
it is recommended to use USB Hard disk drives
(HDD’s).
Recorded programmes are saved into the connected
USB disk. If desired, you can store/copy recordings
onto a computer; however, these ¿les will not be
available to be played on a computer. You can play
the recordings only via your TV.
Lip Sync delay may occur during the timeshifting.
Radio record is supported. The TV can record
programmes up to ten hours.
Recorded programmes are split into 4GB partitions.
If the writing speed of the connected USB disk is not
suf¿cient, the recording may fail and the timeshifting
feature may not be available.
It is recommended to use USB hard disk drives for
recording HD programmes.
Do not plug out the USB/HDD during a recording. This
may harm the connected USB/HDD.
If the AC cord is unplugged while there is an active
USB-recording timer setting, it will be cancelled.
Multipartition support is available. A maximum of two
different partitions are supported. The ¿rst partition of
the USB disk is used for PVR ready features. It also
must be formatted as the primary partition to be used
for the PVR ready features.
Some stream packets may not be recorded because
of signal problems, as a result sometimes videos may
freeze during playback.
Record, Play, Pause, Display (for PlayListDialog) keys
can not be used when teletext is on. If a recording starts
from timer when teletext is on, teletext is automatically
turned off. Also teletext usage is disabled when there
is an ongoing recording or playback.
Watching Recorded Programmes (depending
on the model)
Select Recordings from the Media Browser menu.
Select a recorded item from the list (if previously
recorded). Press the OK button to view the Play
Options. Select an option then press OK button.
Note 9iewing main menu and menu items will not be
available during the pla\bacN.
Press the Stop button to stop a playback and return
to the Recordings.
Slow Forward
If you press Pause button while watching recorded
programmes, the slow forward feature will be
available. You can use Rapid advance button to
slow forward. Pressing Rapid advance button
consecutively will change slow forwarding speed.
Recording Con¿guration
Select the Recording Con¿guration item in the
Media Browser>Settings menu to con¿gure the
recording settings.
Format Disk: You can use the Format Disk feature
for formatting the connected USB disk. Your pin is
required to use the Format Disk feature.
Note: Default PIN can be set to 0000 or 1234. If \ou have
de¿ned the PIN(is requested depending on the countr\
selection) during the First Time Installation use the PIN
that \ou have de¿ned.
IMPORTANT: Formatting your USB drive will erase
ALL the data on it and it’s ¿le system will be converted
to FAT32. In most cases operation errors will be ¿xed
after a format but you will lose ALL your data.
If “USB disk writing speed too slow to record” message
is displayed on the screen while starting a recording,
try restarting the recording. If you still get the same
error, it is possible that your USB disk does not meet
the speed requirements. Try connecting another
USB disk.
English - 13 -
FollowMe TV (depending on the model)
With your mobile device you can stream the current
broadcast from your smart TV using the FollowMe
TV feature. Install the appropriate Smart Center
application to your mobile device. Start the application.
For further information on using this feature refer to
the instructions of the application you use.
Note: 7his application ma\ not be compatible with all
mobile devices. HD channels are not supported and
both of the devices must be connected to the same
networN.
CEC and CEC RC Passthrough (depending on the model)
This function allows to control the CEC-enabled
devices, that are connected through HDMI ports by
using the remote control of the TV.
The CEC option in the System>More menu should be
set as Enabled at ¿rst. Press the Source button and
select the HDMI input of the connected CEC device
from the Source List menu. When new CEC source
device is connected, it will be listed in source menu
with its own name instead of the connected HDMI
ports name(such as DVD Player, Recorder 1 etc.).
The TV remote is automatically able to perform the
main functions after the connected HDMI source has
been selected.
To terminate this operation and control the TV via
the remote again, press Quick Menu button on the
remote, highlight the CEC RC Passthrough and
set as Off by pressing Left or Right button. This
feature can also be enabled or disabled under the
System>More menu.
The TV supports also ARC(Audio Return Channel)
feature. This feature is an audio link meant to replace
other cables between the TV and the audio system
(A/V receiver or speaker system).
When ARC is active, TV does not mute its other audio
outputs automatically. So you need to decrease TV
volume to zero manually, if you want to hear audio
from connected audio device only (same as other
optical or co-axial digital audio outputs). If you want
to change connected device’s volume level, you
should select that device from the source list. In that
case volume control keys are directed to connected
audio device.
System Audio Control
Allows an Audio Ampli¿er/Receiver to be used with
the TV. The volume can be controlled using the
remote control of the TV. To activate this feature set
the Speakers option in the System>More menu as
Ampli¿er. The TV speakers will be muted and the
sound of the watched source will be provided from
the connected sound system.
Note: 7he audio device should support S\stem Audio &ontrol
feature and CEC option should be set as Enabled.
E-Manual (depending on the model)
You can ¿nd instructions for your TV’s features in
the E-Manual.
To use E-Manual, press to the Info button while main
menu is displayed on the screen or press Quick Menu
button, select Information Booklet and press OK.
By using the directional buttons select a desired
category. Every category includes different topics.
Select a topic and press OK to read instructions.
To close the E-Manual screen press the Exit or Menu
button.
Note: 7he contents of the (-0anual ma\ var\
according to the model.
Loading ...
Loading ...
Loading ...