Loading ...
Loading ...
Loading ...
Safety Instructions For Table
- Use extra supports (tables_ saw horses blocks, etc._
for any workpieces large enough to tip when not hold
down to the table top. Never use anolher person as a
substitute for a table extension, or as additional sup.
port for a workpiece that Ls longer or wJder than the
basic saw table, or to help feed. support or pull the
werkpiece.
"Never confine the piece being cut off. that is the piece
not against the rip fence, miter gauge or fixture Never
Plan Ahead To Protect Your Eyes,---aanes, Face
Dress for safety
* Do no! wear loose c othing, gloves, neckties or jewelry
(rings wrist watches). -[hey can get caught and draw
you into moving parts.
- Wear nonslip footwear
- Tie back Ion.g hair.
o Roll tong sleeves above the elbow
-Noise levels vary widely. To avoid possible hearing
damage, wear ear plugs or muffs when using table
saw for hours at a time.
° Any power saw can throw foreign objects into the
eyes. ]"his can result in permanent eye damage. Wear
safety goggles (not glasses) that comply with ANSI
Z87 I (sl)own on package). Everyday eyeglasses have
only impact resistant lenses. They are not safety
glasses. Safety goggles are available at Sears retail
stores. Glasses or goggles not in compliance with
ANSI Z87.1 could seriously hurt you when they break.
WEAR YOUR
-For dusty operations, wear a dust mask along with
safety goggles
lu
Whenever Sawblade is Spinning
WARNING: Don't allow familiarity (gained from Ire- ]
cluent use of your table saw) to cause a careless/
mistake. Always remember that a careless fraction /
of a second is enough to cause a severe injury, /
° Before actually cutting with the saw, watch it while it
runs for a short while, if it makes an unfamiliar noise or
vibrates a IoL stop immediately. Turn the saw off,
Unplug the saw. Do nol restart until finding and cor-
recting the problem.
- Make sure the top of the arbor or cutting tool turns
toward the front of the saw.
Keep Children Away,
- Keep all visitors a safe distance from the table saw.
° Make sure bystanders are clear of the table saw and
workpJece.
Saws (continued) ...................
hold it. clamp it. touch it. or use length stops against it.
It must be free to move. If confined, it could get
wedged against the blade and cause a kickback or
throwback_
Never cut more than one workpiece at a time.
"Never turn your table saw "ON" before clearing every-
thing except the workpiece and related support
devices off the table,
and Ears
Plan the way you will push the workpiece through.
-Never pull the workpiece through. Start and finish
the cut from the front of the table saw.
- Never put your fingers or hands in the path of the
sawblade or other cutting tool
" Never reach in back of the cutting tool with either
hand to hold down workpiece, support the workpiece.
remove wood scraps, or for any other reason.
• Avoid hand positions where a sudden slip could cause
fingers or hand to move into a sawblade or other cut-
ting tool.
• Don't overreach. Always keep good footing and balance_
° Push the workpiece against the rotation el the blade.
never feed material into the cutting tool from the rear of
the saw.
• Always push the workpiece all the way past the saw-
blade.
• As much as possible, keep your face and body to one
side of the sawblade, out of line with a possible kick-
back or throwback.
• Set the cutting tool as low as possible for the cut you're
planning.
Avoid Accidental Starting.
° Make sure switch is "OFF" before plugging saw into a
power outlet.
Don't Force Tool.
- Let the blade reach full speed before cuthng.
° It will do the job better and safer at its designed rate.
= Feed the workpiece into the saw only fast enough to let
the blade cut without bogging down or binding.
Before freeing jammed material.
° Turn switch "OFF",
o Wait for all mowng parts to stop.
° Unplug the saw.
- Check blade, spreader and fence for proper alignment
before starting again,
To avoid throwback of cut off pieces.
• Use the guard assembly.
Loading ...
Loading ...
Loading ...