Loading ...
Loading ...
Loading ...
F©RE YOU CALL FOR
FIRST_
• Check if oven controls have been prop-
erly set.
• Check to be sure plug is securely inserted
into receptacle.
• Checkor re-setdrcuk breaker. Check or
replace fuse.
• Check power supply.
PART OR ALL OF APPLIANCE DOES
NOT WORK.
° Check if surface and/or oven controls
have been properly set. See pgs. 4 & 9.
Check if oven door is unlocked after self-
clean cycle. Seepg. 17.
• Check if oven is set for a delayedcoo[<or
dean program. Seepgs. [ [ & [7.
• Check if Control Lock isactivated. Seepg.
15.
BAKING RESULTS ARE NOT AS
EXPECTED OR DIFFER FROM
PREVIOUS OVEN.
• Hake sure the oven vent has not been
blocked. See pg.8 for location.
• Check to make sure range is [eve[.
• Temperatures often vary between a new
oven and an old one. As ovens age, the
oven temperature often "drifts" and may
become hotter or cooler. See pg. [ 5 for
instructions on adjusting the oven tem-
perature. NOTE: [t is not recommended
to adjust the temperature if only one or
two recipes are in question.
• Checkthat oven temperature isdecreased
by 25° Fwhen convect baking.
° See "Cooking Made Simple" booklet
for more information on bakeware and
baking.
FOOD Is NOT BROILING PRO-
PERLY OR SMOKES EXCESSIVELY.
° Check oven rack positions. Food may be
too dose to element
° Broil dement was not preheated.
° Aluminum foil wasincorrectly used.Never
line the broiler insert with foil.
• Oven door was closed during broiling.
Leave the door open to the first stop
position (about 4 inches).
° Trim excess fat from meat before broiling.
• A soiled broiler pan was used.
OVEN WILL NOT SELF-CLEAN.
• Check to make surethe cycle isnot setfor
a delayed start. See pg. [7.
° Check if door is dosed.
OVEN DID NOT CLEAN PROPERLY.
° Longer cleaning time may be needed.
° Excessivespiiiovers,especiallysugaryand/
or acidic foods, were not removed prior
to the serf-dean cycle.
OVEN DOOR WILL NOT UNLOCK
AFTER SELF-CLEAN CYCLE.
• Oven interior is still hot. Aiiowaboutone
hour for the ovento coo[ after the comple-
tion of a serf-deancycle. The door can be
opened when the LOC indicator word is
VENTILATION FAN DOES NOT
OPERATE BUT EVERYTHING ELSE
ON THE RANGE DOES.
° Check behind lower accesspanelif power
cord to blower assemblyhasbeen discon-
nected.
ORILL HEATING ELEMENT OR
COOKTOP DOES NOT GET HOT
ENOUGH.
° Check if heating dement is plugged in
solidly.
° Surfacecontrols maynot be set properly.
° Vokage to house may be low.
VENTILATION SYSTEM IS NOT
CAPTURING SMOKE EFFICIENTLY.
• Check on cross ventilation in room or
make up air.
° Excessiveamount of smoke is beingcre-
ated; check instructions for grilling, trim-
ming meats. See pg. 6.
• Outside wall cap may be trapped shut.
22
• Rangemay be improperly installed; check
ducting information. Seepg. 3.
° Air filter may be improperly installed. See
pg. 8.
I_/_OISTURE COLLECTS ON OVEN
WINDOW OR STEAM COMES FROM
OVEN VENT.
• This is normal when cooking foods high in
moisture.
° Excessivemoisture was usedwhen cleaning
the window.
THERE IS A STRONG ODOR OR
LIGHT SMOKE WHEN OVEN IS
TURNED ON.
• This is normal for a new range and wiil
disappearafter afew uses. Initiating adean
cyclewill "burn off" the odors more quickly.
• Turning on the ventilation fan wiil help
remove the smoke and/or odor.
° Excessivefood soils on the oven bottom.
Use a self-cleancycle.
A FAN SOUND CAN BE HEARD
• This is the coding fan andis normal. The fan
wii[ continue to run after use until the oven
COalS,
"F" PLUS A NUMBER AND THE
MESSAGE: "CALL AN AUTHO-
RIZED SERVICER OR g00-6gg-
1100o"
° This is called a fauk code. [fa fauk code
appears in the display and beeps sound,
pressthe Cancel pad. If the fault code and
beeps continue, disconnect power to the
appliance.Wait afew minutes, then recon-
nect power. If fault code and beeps still
continue, disconnect power m the appli-
ance and call an authorized servicer.
• If the oven is heavily soiled, excessive flare-
ups may resuk in a fauk code during a clean
cycle. Press Cancel pad and allow the oven
to cool completely, wipe out excess soil,
then reset the clean cycle. Ifthe fault code
and beeps still continue, disconnect power
to the appliance and call an authorized
servicer.
Loading ...
Loading ...
Loading ...