Loading ...
Loading ...
Loading ...
Creating an Auto Accompaniment (User Rhythm)
EN-80
■ User Rhythm Recording Settings
Initial default setting values are indicated by an asterisk (*).
• The operation shown here is performed as the steps of the
procedures below.
– Step 9 under “To create a totally new rhythm and save it”
(page EN-75)
– Step 9 under “To edit an existing rhythm and save it”
(page EN-76)
– Step 5 under “To configure only the mixer settings of an
existing rhythm and save it” (page EN-78)
1.
Long-press 9 PART (MIXER) until the
[MIXER] indicator appears.
This displays the Part On/Off status of the part being
edited.
2.
Use the [2] (w) and [5] (q) bm number keys to
display the menu item you want to change.
• Initial default setting values are indicated by an
asterisk (*).
*1 Only drum set tones can be selected for Drums and
Percussion parts. Drum set sounds cannot be selected for
the bass and the Chord 1 through Chord 5 parts.
3.
Use bn [–] and [+] or the bl dial to change the
setting value.
4.
When mixer settings are the way you want,
press the [4] (EXIT) bm number key.
Item Name
(Display)
Description Settings
Quantize
(Quantize)
Specify either recording of notes
in the timing they are played on
the keyboard or automatic
alignment of notes based on a
note value. Selecting a setting
other than “Off” displays a note
value (4: quarter note, d: dotted
note, t: triplets).
Off*, 4, 8,
16, 32, 4d,
8d, 16d,
32d, 4t, 8t,
16t, 32t
Precount
(Precount)
Specifies whether a precount
should sound before recording
starts after ck START/STOP is
pressed in recording standby.
Selecting “1” sounds a one-
measure precount, while “2”
sounds a two-measure precount.
Selecting “Off” turns off the
precount, so recording starts as
soon as ck START/STOP or a
keyboard key is pressed.
Off, 1*, 2
Play Chord
(PlayChrd)
Starting recording of an
accompaniment pattern starts
repeat playback of all the parts of
the pattern, except for the part
being recorded. During such
repeat playback, you can use
this setting to specify the chord
type to be used for playback by
bass and chord parts. Available
settings are “C” (C major), “C7”
(C 7th), and “Cm” (C minor).
Selecting “Off” turns off bass and
chord part notes.
Off, C*,
C7, Cm
Metronome
(Metronom)
Specifies whether or not the
metronome should sound during
recording.
On, Off*
To configure mixer settings of a part being
edited
Item Name
(Display)
Description Settings
Part On/Off
(Part)
Specifies on/off for the
selected part.
On*, Off
Part tone
(Tone)
Specifies the tone of the
selected part.
*
1
Volume
(Volume)
Adjusts the volume level of
the selected part.
0 to 127*
Pan (Pan) Specifies the stereo pan
position of the selected
part. 0 indicates the center,
while a smaller value shifts
to the left and a larger
value shifts to the right.
–64 to 0* to 63
Reverb Send
(Rev Send)
Specifies how much reverb
is applied to the selected
part.
0 to 40* to 127
Chorus Send
(Cho Send)
Specifies how much
chorus is applied to the
selected part.
0* to 127
Delay Send
(Dly Send)
Specifies how much delay
is applied to the selected
part.
0* to 127
CT-X9000_8000IN_EN.book 80 ページ ２０１８年４月１２日 木曜日 午後１時８分
Loading ...
Loading ...
Loading ...