Loading ...
Loading ...
Loading ...
WHAT TO DO IN AN EMERGENCYWHAT TO DO IN AN EMERGENCY
WHAT TO DO IN AN EMERGENCYWHAT TO DO IN AN EMERGENCY
WHAT TO DO IN AN EMERGENCY
3-6
AS30130A
WARNING:WARNING:
WARNING:WARNING:
WARNING:
Wheel covers may have sharp edges. Han-Wheel covers may have sharp edges. Han-
Wheel covers may have sharp edges. Han-Wheel covers may have sharp edges. Han-
Wheel covers may have sharp edges. Han-
dle them carefully to avoid possible severedle them carefully to avoid possible severe
dle them carefully to avoid possible severedle them carefully to avoid possible severe
dle them carefully to avoid possible severe
injury.injury.
injury.injury.
injury.
Before putting the wheel into place, be sureBefore putting the wheel into place, be sure
Before putting the wheel into place, be sureBefore putting the wheel into place, be sure
Before putting the wheel into place, be sure
that there is nothing on the hub or wheelthat there is nothing on the hub or wheel
that there is nothing on the hub or wheelthat there is nothing on the hub or wheel
that there is nothing on the hub or wheel
(such as mud, tar, gravel, etc.) that inter-(such as mud, tar, gravel, etc.) that inter-
(such as mud, tar, gravel, etc.) that inter-(such as mud, tar, gravel, etc.) that inter-
(such as mud, tar, gravel, etc.) that inter-
feres with the wheel fitting solidly againstferes with the wheel fitting solidly against
feres with the wheel fitting solidly againstferes with the wheel fitting solidly against
feres with the wheel fitting solidly against
the hub. If there is, remove it. If there is notthe hub. If there is, remove it. If there is not
the hub. If there is, remove it. If there is notthe hub. If there is, remove it. If there is not
the hub. If there is, remove it. If there is not
good contact on the mounting surface be-good contact on the mounting surface be-
good contact on the mounting surface be-good contact on the mounting surface be-
good contact on the mounting surface be-
tween the wheel and hub, the wheel nutstween the wheel and hub, the wheel nuts
tween the wheel and hub, the wheel nutstween the wheel and hub, the wheel nuts
tween the wheel and hub, the wheel nuts
could come loose and cause the loss of acould come loose and cause the loss of a
could come loose and cause the loss of acould come loose and cause the loss of a
could come loose and cause the loss of a
wheel. Loss of a wheel may result in loss ofwheel. Loss of a wheel may result in loss of
wheel. Loss of a wheel may result in loss ofwheel. Loss of a wheel may result in loss of
wheel. Loss of a wheel may result in loss of
control of the vehicle. This may cause seri-control of the vehicle. This may cause seri-
control of the vehicle. This may cause seri-control of the vehicle. This may cause seri-
control of the vehicle. This may cause seri-
ous injury or death.ous injury or death.
ous injury or death.ous injury or death.
ous injury or death.
D060I01E-GAT
8. Lower Vehicle and Tighten Nuts8. Lower Vehicle and Tighten Nuts
8. Lower Vehicle and Tighten Nuts8. Lower Vehicle and Tighten Nuts
8. Lower Vehicle and Tighten Nuts
D060H01A-AAT
7. Re-install Wheel Nuts7. Re-install Wheel Nuts
7. Re-install Wheel Nuts7. Re-install Wheel Nuts
7. Re-install Wheel Nuts
To reinstall the wheel cover, hold it on the wheel
and put the wheel nuts on the studs and tighten
them finger tight. The nuts should be installed
with their small diameter ends directed inward.
Jiggle the tire to be sure it is completely seated,
then tighten the nuts with your fingers again.
Lower the car to the ground by turning the
wheel nut wrench counterclockwise. Then posi-
tion the wrench as shown in the drawing and
tighten the wheel nuts. Be sure the socket is
seated completely over the nut. Do not stand on
the wrench handle or use an extension pipe
over the wrench handle.
Go around the wheel tightening every other unt
until they are all tight. Then double-check each
nut for tightness. After changing wheels, have a
technician tighten the wheel nuts to their proper
torque as soon as possible.
Wheel nut tightening torque:Wheel nut tightening torque:
Wheel nut tightening torque:Wheel nut tightening torque:
Wheel nut tightening torque:
Steel wheel & aluminium alloy wheel:
900-1,100 kg.cm (65-80 lb.ft)
D060H01A
HNVOM098
Loading ...
Loading ...
Loading ...