Loading ...
Loading ...
additional
BEFORE USING THE SAW:
instructions for radial
arm saws
.e..d
3 =
€_
e--
WARNING: TO AVOID MISTAKES THAT COULD
RESULT IN SERIOUS, PERMANENT INJURY, DO
NOT CONNECT POWER CORD UNTIL THE FOL-
LOWING STEPS HAVE BEEN SATISFACTORILY
COMPLETED:
1. Assembly and alignment. (See pages 12-31)
2. Examination and operating familiarity with ON-
OFF switch, elevation hand wheel, swivel lock,
bevel lock and rip lock, guard clamp screw,
spreader and anti-kickback device and miter
lock. (See pages 37, 38 & 39.)
3. Review and understanding of all safety instruc-
tions and operating procedures throughout the
manual.
FOB YOUR OWN SAFETY:
1 Read an€ uncle(stand owner's _anua_
before 3perating machine
2 Wear s_,ely goggles compqying wilh
ANSI Z87 1
3 Keep hands Ou{ o1 path o¢ saw blade
4. Know he* to avoid "KICKBACKS.
5 USe "PUSH STfC K • for qarrow work
6 Never reach around Ihe saw blade
? Never perlorm any opef|l_on
'FREEHANO '
8 Returp carriaQe I_ the full rear posi_on
8fief e_h cros_ cul type o_ration
s shulof,po*ermad ai_ow_aw b_.d_Io
stop befo(e Ddiusllng of se_mcing
Read the following danger labels which appear on
the front of the radial arm saw base assembly, motor
and saw guard: _ WHENRIPPING
-- - TO AVOID m.'NAW=Y WORKm_OE
_ _ DA_R AT C,tn_
Know this tool:
1, Read and Under,land all warnlng_ an(3 instructlon_ o_
Saw, in Owners Manual and wilh recommended accea-
ttodes.
2 Properly guard the cuf_ng 3 Provtde proper workpl_e
tool. aupporl
4 Positlo_ the cutting _ool
.__ b_hind the lance by mov
Ing Ihe _rm to the tef'_ and
clamping the yoke SO this
label fa_n the lance; or
construct an au xill_ry
fence per Owner's Man-
ual
5 With power off Ihe aw+tch
-- key removed, 1urn cutting
1_ by hand qo make sure
It do_a no_ strike guard,
o3_f _ fl fence or any other saw
parts [[0,_,=_
WHEN INSTALLING OR MOVING THE
SAW
1. To avoid injury from unexpected carriage travel,
lock the rip lock handle before moving the saw.
2. To avoid injury from unexpected saw movement:
(a) Bolt the saw to the floor if it tends to slip,
walk, or slide during normal operation.
(b) When table extensions over 24" wide are
added to either side of the saw, make sure
you either bolt the saw to the floor or support
the outer end of the extension from the floor
as appropriate.
3. To avoid injury from unexpected carriage travel
adjust leveling feet so the arm tilts slightly
downward to the rear so that the carriage will not
roll forward due to gravity. Forward drift of the
carriage on an improperly leveled saw could
cause the blade to lunge forward due to un-
expected contact with the workpiece, fence,
table or part of your body.
BEFORE EACH USE
Plan your work.
-- To avoid injury from accidental starting, always
remove the plug from the outlet, turn the switch
off and remove the switch key before removing
the guard, changing the cutting tool, changing
the setup or making adjustments.
To avoid injury from blade contact, slips, shocks,
thrown pieces, etc., check the saw to make sure
that no parts are missing or broken, bent, or have
failed in any way, or any electrical component
fails to perform properly. Shut off power switch,
pull the plug from the outlet and replace damaged,
missing and/or failed parts before resuming
operation.
To avoid injury from electrical shock, make sure
your fingers do not contact the terminals when
installing or removing the plug to or from a live
outlet.
Check the fence for proper workpiece support. To
avoid fence breakage which could result in thrown
workpieces and blade contact, do not use fences
made of particle board or other composite
materials - use 3/4" thick lumber long enough to
extend in one piece from end to end of the saw
table, and tall enough to be at least even with the
top of the workpiece. Replace any fence where
existing slots in the fence have weakened the
fence or can snag the workpiece during ripping
operations. Always check table locks to make
sure any new fence is held securely (see page 27).
Choose your cutting tool carefully. Many saw
accidents are caused by use of the wrong type
blade, dull, badly set, improperly sharpened cut-
ting tools, gum or resin adhering to the cutting
tools, and by blade misalignment with the saw
fence. Such conditions can cause the material to
stick, jam (stall the saw), throw or "kickback" the
workpiece at the operator.
To avoid cutting tool failure and thrown shrapnel
(broken pieces of blade), use only blades or other
cutting tools marked for operating speeds 3450
rpm or higher. Never use a cutting tool larger in
diameter than the diameter for which the saw was
designed.
To avoid jamming of the blade, thrown work-
pieces, and damage to the blade collars, never
use a broken, warped, or unbalanced blade. Do
not overtighten arbor nut. Use arbor wrenches to
"snug" it securely.
To avoid injury from accidental blade contact by
the workpiece or the operator do not perform
layout, assembly, or setup work on the table
Loading ...
Loading ...
Loading ...