Loading ...
Loading ...
Loading ...
En
40
Setting the unit display section
brightness
! By default, the level is set to 3.
1 Press the [WAKE UP (UTILITY)] button for over 1
second.
The utilities screen appears on a display of this unit.
2 Use the rotary selector to select and enter [LCD
BRIGHTNESS].
Use the rotary selector to select and enter a value from [1] (Dark) to [5]
(Bright).
Changing the demo mode and screen
saver function setting
On this unit, the demo mode is set if no operation is performed for
10 minutes under normal usage conditions. This demo mode can be
changed.
! By default, demo mode starts when there is no operation for 10
minutes.
! When any control or button on this unit is operated while in the
demo mode, the demo mode is canceled.
! The screen saver function setting can be selected instead of demo
mode. The screen saver starts when there is no operation for 30
minutes.
1 Press the [WAKE UP (UTILITY)] button for over 1
second.
The utilities screen appears on a display of this unit.
2 Use the rotary selector to select and enter
[DEMO / SCREEN SAVER].
3 Use the rotary selector to select and enter one of the
settings.
— DEMO (10 min): Demo mode starts when there is no operation
for 10 minutes.
— DEMO (5 min): Demo mode starts when there is no operation for
5 minutes.
— DEMO (1 min): Demo mode starts when there is no operation for
1 minute.
— SCREEN SAVER: Enables the screen saver function.
— DISABLED: Disables the demo mode and screen saver function.
Correct the alignment of touch display
1 Press the [WAKE UP (UTILITY)] button for over 1
second.
The utilities screen appears on a display of this unit.
2 Use the rotary selector to select and enter [TOUCH
DISPLAY CALIBRATION].
3 Use the rotary selector to select and enter one of
[CENTER], [LEFT], and [RIGHT].
— [CENTER]: Center touch display
— [LEFT]: Left touch display
— [RIGHT]: Right touch display
4 Touch [+] displayed on the screen, in order.
Touch 4 places in all.
5 Press the rotary selector to enter.
The changed settings are stored.
! This unit has been shipped after calibration. Set the calibration again
if you cannot touch properly.
! When setting the calibration, do not use a pointed object like a
ball-pen.
Setting monaural/stereo of master
output
! By default, stereo is set.
1 Press the [WAKE UP (UTILITY)] button for over 1
second.
The utilities screen appears on a display of this unit.
2 Use the rotary selector to select and enter [MASTER
OUT].
3 Use the rotary selector to select and enter [MONO] or
[STEREO].
— MONO: Outputs the master sound in monaural.
—
STEREO: Outputs the master sound in stereo.
Setting monaural/stereo of booth output
! By default, stereo is set.
1 Press the [WAKE UP (UTILITY)] button for over 1
second.
The utilities screen appears on a display of this unit.
2 Use the rotary selector to select and enter [BOOTH
OUT].
3 Use the rotary selector to select and enter [MONO] or
[STEREO].
— MONO: Outputs the booth sound in monaural.
—
STEREO: Outputs the booth sound in stereo.
Setting the operation of the microphone
sound low cut filter
Set whether or not to apply a filter to attenuate sounds lower than the
human voice to microphone sound.
! By default, the low cut filter is set to [ON (Enabled)].
1 Press the [WAKE UP (UTILITY)] button for over 1
second.
The utilities screen appears on a display of this unit.
2 Use the rotary selector to select and enter [MIC LOW
CUT].
3 Use the rotary selector to select and enter [ON] or
[OFF].
— ON: Enables the low cut filter of microphone sound.
— OFF: Disables the low cut filter of microphone sound.
Setting the limiter of microphone audio
added to master output
! By default, the limiter is set to [OFF (Disabled)].
1 Press the [WAKE UP (UTILITY)] button for over 1
second.
The utilities screen appears on a display of this unit.
2 Use the rotary selector to select and enter [MIC
LIMITER FOR MASTER].
3 Use the rotary selector to select and enter one of
[OFF], [0 dB], [3 dB], [6 dB], [9 dB], [12 dB], and [15 dB].
Loading ...
Loading ...
Loading ...