Loading ...
Loading ...
Loading ...
- 7
1 Lever for seat adjustment
2 Driver seat
Pull seat adjustment lever outwards.
Slide seat, release lever and lock in place.
Check that the seat is properly locked in
position by attempting to move it back-
wards and forwards.
Open the gas drawing valve by turning
it in anti-clockwise direction.
Note: The machine is equipped with a seat
contact switch If the driver's seat is vacat-
ed, the machine is switched off.
Sit on the driver's seat.
Lock parking brake (11).
Push motor speed adjustment (10) 1/3
to the front.
Press the brake pedal in order to start
the engine.
During cold exterior temperatures: Pull
the choke (13).
Turn the ignition switch to the right and
start the device.
If the machine starts, release the igni-
tion key.
If the motor runs smoothly, push in the
choke.
Note: Never operate the starter motor for
longer than 10 seconds. Wait at least 10
seconds before operating the starter motor
again.
1 Brake pedal
2 Accelerator pedal, "forwards"
3 Accelerator pedal, "reverse"
Push the motor speed adjustment all
the way to the front (operating speed).
Press brake pedal and keep it de-
pressed.
Release parking brake.
Press slowly the accelerator pedal "for-
ward".
DANGER
Risk of injury!
When reversing, there must not be any
risk for third parties, have somebody
marshal the driver if necessary.
Press slowly the accelerator pedal "re-
verse".
The accelerator pedal can be used to
vary the driving speed infinitely.
Avoid sudden operation of the pedal as
this may damage the hydraulic system.
In the event of power loss on inclined
surfaces, slightly reduce the pressure
on the accelerator pedal.
Release the accelerator pedal, the ma-
chine brakes automatically and stops.
Note: The braking effect can be supported
by pressing the brake pedal.
Driving over fixed obstacles which are 70
mm high or less:
Drive forwards slowly and carefully.
Driving over fixed obstacles which are
more than 70 mm high:
Only drive over these obstacles using a
suitable ramp.
ATTENTION
Do not sweep up packing strips, wire or
similar objects as this may damage the
sweeping mechanism.
Note: To achieve an optimum cleaning re-
sult, the driving speed should be adjusted
to take specific situations into account.
Note: During operation, the dust filter
should be shaken off and cleaned at regu-
lar intervals.
Note: When frequently working in areas
with fine dust, the filter must be cleaned
more often.
1 Roller brush and side brush control le-
ver
2 Control lever waste container
3 Roller brush control lever
4 Control lever container flap
Roller brush and side brush control lever
Control lever (1) forwards: Switches the
roller brush on and lowers and switches
the side brushes on.
Control lever (1) backwards: Switches
the roller brush on.
Control lever waste container
Control lever waste container (2) to the
front: Waste container is lowered.
Control lever waste container (2) to the
back: Waste container is raised.
Control lever roller brush
Roller brush control lever (3) forwards:
Raises the roller brush.
Roller brush control lever (3) back-
wards: Lowers the roller brush.
Control lever container flap
Control lever container flap (4) to the
front: The container flap of the waste
container opens.
Control lever container flap (4) to the
back: The container flap of the waste
container closes.
Switch on the blower.
With surface cleaning:
Roller brush and side brush control le-
ver (1) backwards: Switches the roller
brush on.
Roller brush control lever (3) back-
wards: Lowers the roller brush.
Control lever container flap (4) to the
front: Container flap opens.
With cleaning of side edges:
Roller brush and side brush control le-
ver (1) forwards: Switches the roller
brush on, switches the side brushes on
and lowers them.
Roller brush control lever (3) back-
wards: Lowers the roller brush.
Operation
Adjusting driver's seat
Open the gas supply
Starting the machine
Start the engine
Drive the machine
Drive forward
Reverse drive
Driving method
Brakes
Driving over obstacles
Sweeping mode
Control lever
Sweeping dry floors
25EN
Loading ...
Loading ...
Loading ...