Loading ...
Loading ...
Loading ...
- 5
DANGER
Risk of injury and damage! Do not use a
forklift to unload the appliance.
To unload the machine, proceed as follows:
Cut plastic packing belt and remove foil.
Remove the elastic tape fasteners at
the stop points.
Four indicated floor boards of the pallet
are fastened with screws. Unscrew
these boards.
Place the boards on the edge of the pal-
let. Place the boards in such a way that
they lie in front of the four wheels of the
machine. Fasten the boards with
screws.
Slide the four support beams included
in the packaging under the ramp.
Remove the wooden blocks used for ar-
resting the wheels and slide them under
the ramp.
Danger
Risk of injury! Before engaging the free-
wheel operation, the machine must be se-
cured to prevent it rolling away.
NOTICE
Do not move the machine for long distanc-
es without engaging self-propulsion, a
speed of 6 km/h should not be exceeded.
1 Position of the freewheel lever up - ap-
pliance can be pushed.
Opening and securing cover
Engage the freewheel lever in the upper
position.
This blocks the travel drive function.
Close cover.
The machine can now be pushed.
1 Position freewheel lever down - appli-
ance is ready to start.
Engage the freewheel lever in the lower
position.
Close cover.
The appliance can now be driven.
Park the sweeper on an even surface.
Remove the key.
몇 WARNING
Only type-tested replacement bottles (pow-
er gas bottles) with 11 kg of content must
be used. These have a 270° collar for the
protection of the valve.
Danger
Risk of injury!
– Follow safety regulations for LPG vehi-
cles.
– Formation of crusts and yellow-frothing
deposits on the gas cylinder indicate
leakiness.
– Cylinders must be changed only by in-
structed persons.
– Cylinders containing propellant gases
must not be changed in garages and
underground areas.
– Do not smoke and use uncovered light
while changing the cylinder.
– While changing cylinders, first close the
locking valve of the LPG cylinder firmly
and immediately put the protective cap
on the empty cylinder.
1 Protective cover
2 Union joint
3 Gas withdrawal valve
4 Fixing
Insert the gas cylinder in the fixing; the
gas cylinder connection must point up-
wards.
Illustration: shown without gas cylinder
1 Lock
2 Safety splint
3 Fastening belt
Close the lock on the fastening belt.
Attach safety splint.
NOTICE
Connection has a left threading.
몇 WARNING
Do not open the gas drawing valve until be-
fore starting the device (refer to chapter
"Operation | Driving").
몇 WARNING
Danger through escaping gas. Route/at-
tach the gas hose so that it does not pro-
trude outside the appliance and cannot be
torn off during operation.
Remove the protective cap from the
connecting valve of the gas cylinder.
Connect the gas tube with Union nut
(use 30 mm spanner).
KM 100/100 R G only
Danger
Risk of explosion!
– Only use the fuels specified in the Op-
erations Manual.
– Do not refuel the machine in enclosed
spaces.
– Smoking and naked flames are strictly
prohibited.
– Ensure that no fuel reaches the hot
open surfaces.
Switch off engine.
Opening and securing cover
Check fuel level via the tank indicator.
Open fuel filler cap.
Use "regular unleaded petrol".
Fill tank to max. 1 cm below the lower
edge of the filler nozzle.
Wipe off any spilt fuel, remove funnel
and close fuel filler cap.
Close cover.
Before Startup
Unloading
Moving sweeper without engaging
self-propulsion
Moving sweeper by engaging self-
propulsion
Start up
General notes
Connect/ change gas cylinder (only
KM 100/100 R LPG)
Attach gas cylinder
1
2
3
4
Fasten gas cylinder
Connect gas cylinder
Refuelling
21EN
Loading ...
Loading ...
Loading ...