Loading ...
Loading ...
Loading ...
Trademarks are the property of Koninklijke Philips N.V. or their
respective owners.
Funai
Corporation reserves the right to change products at any
time without being obliged to adjust earlier supplies
accordingly.
The material in this Owner's manual is believed adequate for
the intended use of the system. If the product or its individual
modules or procedures are used for purposes other than those
specified herein, confirmation of their validity and suitability
must be obtained. Funai Corporation warrants that the material
itself does not infringe any United States patents. No further
warranty is expressed or implied.
Funai Corporation cannot be held responsible neither for any
errors in the content of this document nor for any problems as
a result of the content in this document. Errors reported to
Funai Corporation will be adapted and published on the Funai
Corporation support website as soon as possible.
Pixel characteristics
This LCD product has a high number of color pixels. Although it
has effective pixels of 99.999 % or more, black dots or bright
points of light (red, green or blue) may appear constantly on
the screen. This is a structural property of the display (within
common industry standards) and is not a malfunction.
Warranty
No components are user serviceable. Do not open or remove
covers to the inside of the product. Repairs may only be done
by service centers and official repair shops. Failure to do so shall
void any warranty, stated or implied.
Any operation expressly prohibited in this manual, any
adjustments or assembly procedures not recommended or
authorized in this manual shall void the warranty.
Federal communications commission notice
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
●
Reorient or relocate the receiving antenna.
●
Increase the separation between the equipment and the
receiver.
●
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
●
Consult the dealer or an experienced radio or television
technician for help.
Declaration of conformity
Trade name
: PHILIPS
Responsible party
: Funai Corporation, Inc.
Model
: 75PUL7552/F7, 65PUL7672/F7,
65PUL7552/F7, 55PUL7672/F7,
55PUL7552/F7, 50PUL7672/F7,
50PUL7552/F7, 43PUL7672/F7,
43PUL7652/F7
Address
: 12489 Lakeland Road, Santa Fe
Springs, CA 90670, USA*
Telephone number
: 1 833 978 3323
*
This is not the mailing address for Open Source Software or
Customer service.
Modifications
This apparatus may generate or use radio frequency energy.
Changes
or modifications to this apparatus may cause harmful
interference.
Any modifications to the apparatus must be approved by Funai
Corporation.
The user could lose the authority to operate this apparatus if an
unauthorized change or modification is made.
Cables
Connections to this device must be made with shielded cables
with metallic RFI/EMI connector hoods to maintain compliance
with FCC Rules and regulations.
Canadian notice
CAN ICES-3 (B)/NMB-3 (B)
Analog and digital television receiving apparatus, Canada
BETS-7/NTMR-7.
The following FCC/IC RSS applies to the wireless LAN
adapter included in this product.
FCC caution: Any changes or modifications not expressly
approved by the party responsible for compliance could void
the user's authority to operate this equipment.
This transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
FCC/IC RF Exposure Compliance
This equipment complies with FCC/IC radiation exposure limits
set forth for an uncontrolled environment and meets the FCC
radio frequency (RF) Exposure Guidelines and RSS-102 of the IC
radio frequency (RF) Exposure rules.
This equipment should be installed and operated keeping the
radiator at least 20 cm or more away from your body.
This device complies with Part 15 of FCC Rules and Industry
Canada licence-exempt RSS standard(s). Operation is
subject
to the following two conditions: (1) this device may
not cause interference, and (2) this device must accept any
interference, including interference that may cause
undesired operation of this device.
5150-5250 MHz band is restricted to indoor operations
only.
High-power radars are allocated as primary users (i.e.
priority
users) of the bands 5250-5350 MHz and 5650-5850
MHz and that these radars could cause interference and/or
damage to LE-LAN devices.
Compliance with FCC requirement 15.407(c) and IC
requirement RSS-210A9.4.4
Data transmission is always initiated by software, which is
the passed down through the MAC, through the digital and
analog baseband, and finally to the RF chip. Several special
packets are initiated by the MAC. These are the only ways
the digital baseband portion will turn on the RF transmitter,
which it then turns off at the end of the packet. Therefore,
the transmitter will be on only while one of the
aforementioned packets is being transmitted. In other
words, this device automatically discontinue transmission in
case of either absence of information to transmit or
operational failure.
6 .English
Back to Contents
Loading ...
Loading ...
Loading ...