Loading ...
Loading ...
Loading ...
5. Use (A) and (D) to move the pointer to
[GPS].
6. Press (C).
7. Use (A) and (D) to move the pointer to
[USING GPS].
8. Press (C).
9. Use (A) and (D) to move the pointer to
[ON] (enabled) or [OFF] (disabled).
10. Press (C).
After the setting operation is complete,
[SETTING COMPLETED] will appear for
a few seconds, and then the GPS setting
screen will re-appear.
11. Use (A) and (D) to move the pointer to
[INTERVAL].
This option is for specifying the location
information acquisition interval by GPS
signal reception.
12. Press (C).
13. Use (A) and (D) to select a GPS receive
interval.
[NORMAL]
Acquires location info every
second.
[LONG]
Acquires location info every
minute.
14. Press (C) to complete the setting
operation.
After the setting operation is complete,
[SETTING COMPLETED] will appear for
a few seconds, and then the GPS setting
screen will re-appear.
15. Press (E) twice to exit the setting screen.
Note
●
You can also change the GPS receive
interval using G-SHOCK MOVE.
Checking the Altitude
Differential Between Your
Current Location and a
Checkpoint
You can use G-SHOCK MOVE during run
timing to check the altitude differential
between a checkpoint and your current
location.
●
You can specify up to 10 checkpoints.
1. Enter the Training Mode.
l
Navigating Between Modes
2. Press (D) three times.
This displays the altimeter navigation
screen.
Checkpoint altitude
Current location altitude
Differential between checkpoint
and current altitudes
Travel time
●
A pointer (
) to the right of the scale
along the left of the screen also
indicates the altitude differential
between the checkpoint and current
altitude. The appearance of the pointer
changes as described below.
This
pointer:
Means this:
Altitude differential of +100m (Or:
+100ft) or more
Altitude differential within -100 to
100m (-100 to 100ft)
Altitude differential of -100m (Or:
-100ft) or more
Each press of (A) switches the checkpoint
display.
Important!
●
You can use G-SHOCK MOVE to
specify checkpoints along a running
course. Note that you cannot configure
settings using watch operations.
Setting Up Alerts
You can use G-SHOCK MOVE to specify alert
intervals to keep you informed of your calories
burned, elapsed time, and attained altitude
while training. Then the watch will perform a
sound and/or vibration alert operation
whenever you reach an alert interval value
while training. Use watch operations to enable
or disable alerts.
l
Specifying the Alert Interval (Target Alert)
1. Enter the Timekeeping Mode.
l
Navigating Between Modes
2. Press (C).
This displays the GPS signal receive start
screen.
3. Press (A) or (D).
This displays the Training Mode screen.
4. Hold down (A) for at least two seconds.
This displays the Training Mode setting
screen.
Pointer
5. Use (A) and (D) to move the pointer to
[ALERT].
6. Press (C).
7. Use (A) and (D) to select the item whose
setting you want to change.
[CALORIES] Calories burned
[TIME 1] Time 1
[TIME 2] Time 2
[ALTITUDE] Altitude
8. Press (C).
9. Use (A) and (D) to select an alert setting.
[OFF] Disabled
[ON (REPEAT)] Enabled (repeat)
[ON (1 TIME)] Enabled (one time)
●
While [ON (REPEAT)] is selected, an
alert operation is performed whenever
an alert interval value is reached.
10. Press (C) to complete the setting
operation.
After the setting operation is complete,
[SETTING COMPLETED] will appear for
a few seconds, and then the alert setting
screen will re-appear.
●
If you want to configure settings for
another item, repeat steps 7 through 10.
11.
Press (E) twice to exit the setting screen.
Operation Guide 3475
25
Loading ...
Loading ...
Loading ...