Loading ...
Loading ...
Loading ...
_ @0(! RX-VI400U EN.book Page 27 Thursday, July 10, 20(13
?
12:17 AM
• Troubleshooting for auto setup procedure
Before auto setup
Error message Cause Remedy
Conneo_. M_C! Optiinizer microphone is not connected. • Connect the supplied optimizer microphone to the
OPTIMIZER MIC jack on the front panel.
driP 1Ug HP ! Headphones are connected. • Unplug the headphones.
During auto setup
Press (/) to display Ihe detailed information about the individual error. Select RETRY Io try aulo setup procedure again.
Error message Cause Remedy
E-1;N0 FRONT SP Front L/R channel signal(s/ is (are) not • Salect dle front speakers with SPEAKER A or B.
delected. • Check the front L/R speaker connections.
E-2; NO SURR. SP A surround channel signal is not detected. • Check the surround speaker connections.
E-3; NO PRES. SP A presence channel signal is not delected. • Check the presence speaker connections.
E-4; SBR- >SBL Only right surround back channel signal is • Connect the surround back speaker to the LEFT
delected. SURROUND BACK SPEAKERS terminal if you
only have one smTound back speaker.
E-5 ==NO [ SY Background noise is too loud. • Try auto setup procedm'e in quiet environment.
• Turn off noisy electric equipment like air conditioners
(etc.) or move it away from this unit.
E-_, ; CHEC[( SURe, Surround back speaker(s) is (are) connected, • Connect surround speakers when you use (a)
though surmtmd L/R speakers are not. surround back speaker(s).
E-_;NO N]_C Theoptiinizer microphone w_s unplugged • Connect the supplied optimizer microphone to
during the auto setup procedure. OPTIMIZER MIC jack on the front panel.
E-8:NO S[GHAL Theoptiinizermicrophonedoesnotdetecttes_ • Checkthemicrophonesetting.
tones. • Check the speaker connections and plaeemenL
E-9:USER CANCEL The auto setup procedure w_s cancelled • Perfbrmtheauto_tupprocedure_galn.
because a setting which af'tbcts the auto setup
was changed during lhe procedure.
After auto setup
Press ( / > to display the detailed information about the individual error.
Warning message Cause Remedy
W-1; OUT L'IFPHASE Speaker polarity is not correct. This message • Check the speaker connections.
may appear depending on the speakers even
when the speakers are connected correcdy.
kI-2g0/)ER 24N The distance between the speaker and the • Bring the speaker closer to the listening position.
( 8_ f'_.. ) lislening position is over 24 meters (80fl.).
kI-Z;LEUEL ERROR Thedifl_renceofvolumelevelamongspeakers • Readjust the speaker instatlation.
is excessive. (No level correction is made./ • Check the speaker connections.
• Use speakers of similar quality.
• Adjust the output volume of the subwoofer.
t.,.I-4; SI.dFR PHASE The phase polarity ofthesubwooti:r is not • We recommend that you select the oppesite phase on
correct, the subwoofer if the subwoofer has a phase switch.
kI-5;/)0L ERROR The result inky not be correct because the • Perfbrm the auto setup procedure again. Do not
volume was changed during the auto setup change the volume during the auto setup procedure.
procedure.
+ +
• If the warning message W-2 or W-3 appears on the OSD, no corrections are made. In such cases, correct the problem, select CHECK
in DISTANCE or LEVEL, then perfornl the auto setup procedure again.
• If the message W- I, W-4 or W-5 appears on the OSD, corrections are made. However, the corrections may not be correct. In such
cases, correct the problem, then perfk_rm the auto setup procedure again on the relevant setting items.
27
Loading ...
Loading ...
Loading ...