355-0784
LIMITED LIFETIME WARRANTY
PAGE: 1 / 8
231121
Unpack your fan and check the contents. You should have the following items.
1.) Mounting Plate
2.) Trim Ring
3.) Fan Motor Assembly
4.) Light Kit Pan
5.) Fan Blades (5 PCS)
6.) Glass Shade
7.) LED Module Assembly
8.) Assembly Kit
9.) Installation Instructions
10.) Remote Control Set (Includes & Transmitter & Battery & Screws
& Remote Control Instructions)
Unpack your fan and check the contents. You should have the following items.
1.) Mounting Plate
2.) Fan Motor Assembly with Receiver of Remote Controller
3.) Fan Blades (4 PCS)
4.) Connect Plate of Light Kit
5.) Light Kit with LED Module
6.) Glass Shade
7.) Assembly Kit
8.) Installation Instructions
9.) Remote Control Set (Includes Transmitter & Battery & Screws & Remote Control Instructions)
Dimension Reference:
Package Contents:
1
2
3
4
8
7
6
5
9
10
Installation
Instructions
A
B
D
A. 11-1/2" B. 7" C. 8" D. 44"
X 16
Remote
Control
Instructions
2H 4H 8H
PAGE: 2 / 8
231121
Exploded View Detail
Mounting Plate
Fan Motor Assembly
Fan Blade
Trim Ring
Glass Shade
Light Kit Pan
LED Module Assembly
Unpack your fan and check the contents. You should have the following items.
1.) Mounting Plate
2.) Fan Motor Assembly with Receiver of Remote Controller
3.)
4.) Connect Plate of Light Kit
5.) Fan Blades (4 PCS)
6.) Connect Plate of Light Kit
7.) Light Kit with LED Module
8.) Assembly Kit
9.) Installation Instructions
10.) Remote Control Set (Includes Transmitter & Battery & Screws & Remote Control Instructions)
PAGE: 3 / 8
231121
Safety Instructions
READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN TO
INSTALL THE FAN AND SAVE INSTRUCTIONS.
All set screws of the fan must be checked and retightened where necessary before installation.
To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets,
balancing the blades or cleaning the fan. Do not insert foreign objects between rotating fan blades.
Before changing the fan direction, turn off the fan and wait for the fan blades to stop completely.
The safeguards provided by these safety instructions and by the separate installation
instructions are not meant to cover all possible conditions and situations that may occur. It must be
understood that common sense, caution and care are factors which can not be built into this product.
These factors must be supplied by the person(s) installing, caring for and operating the fan.
TO AVOID RISK OF ELECTRIC SHOCK, BE SURE TO SHUT OFF POWER AT THE MAIN
FUSE OR CIRCUIT BREAKER BOX BEFORE INSTALLING OR SERVICING THIS
FIXTURE. TURNING OFF THE ELECTRICAL POWER BY USING THE LIGHT SWITCH
IS NOT SUFFICIENT TO PREVENT ELECTRICAL SHOCK.
TO REDUCE THE RISK OF INJURY, INSTALL THE FAN SO THAT THE BLADES ARE
AT LEAST 7 FEET (2.1 METERS) ABOVE THE FLOOR AND AT LEAST 18 INCHES
(0.5 METERS) FROM THE TIP OF THE BLADES TO THE WALL.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT
TO OUTLET BOX MARKED "ACCEPTABLE FOR FAN SUPPORT" AND USE MOUNTING
SCREWS PROVIDED WITH THE OUTLET BOX.
THE INSTALLATION HAS TO BE IN ACCORDANCE WITH THE NATIONAL ELECTRICAL
CODE, ANSI/NFPA 70-1999 AND LOCAL CODES. IF YOU ARE UNFAMILIAR WITH THE
METHODS OF INSTALLING ELECTRICAL WIRING, SEEK THE SERVICES OF A
QUALIFIED LICENSED ELECTRICIAN.
WARNING
PAGE: 4 / 8
231121
Installation Steps :
Attach the trim ring to the fan motor
assembly from the opening of the
motor housing at an angle. Make
sure the studs of trim ring are on
top.
INSTALLATION INSTRUCTIONS
NOTE: The fan weight is 15.21 lbs (6.9 kg). Be sure the outlet box you are using is securely attached to the building
structure and can support the full weight of the fan. Failure to do so can result in serious injury.
IMPORTANT:
BEFORE YOU BEGIN INSTALLING THE FAN, CAREFULLY READ ALL INFORMATION N THE SEPARATE
SHEET "SAFETY INSTRUCTIONS" AS WELL AS THE FOLLOWING "INSTALLATION INSTRUCTIONS". IF IN
DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
SAVE ALL INSTRUCTIONS.
The receiver is already fixed in the
housing.
Carefully lift the fan motor assembly and
hang the fan motor assembly on the hook
of the mounting plate by utilizing one of
the holes at the outer rim of the motor
housing so that it is securely suspended.
Then connect the wiring to your fan
according to step 6 "Making the Electrical
Connections".
Fig.1
Turn OFF the electric power at the
main fuse or circuit breaker box.
Pull the wires from outlet box through the
center hole of mounting plate. Attach the
mounting plate to the outlet box, then align
and engage the bottom holes from outlet
box to the holes of mounting plate then fix
them together with washers and screws
from outlet box or assembly kit bag.
WARNING: MOUNT ONLY TO AN
OUTLET BOX MARKED "ACCEPTABLE
FOR FAN SUPPORT"!
Mounting Plate
Outlet Box
Washer
Mounting Screw
Fig.2
PAGE: 5 / 8
Fan Motor
Assembly
Stud
Trim Ring
Fig.4
Fan Motor
Assembly
Receiver
Fig.3
Mounting
Plate
Fan Motor
Assembly
Trim Ring
Fig.5
Fig.6
Connect the ground wires (Green or bare
copper) coming from outlet box, mounting
bracket with a wire connector.
After making the wire connections, the wires
should be spread apart. The white (neutral)
conductor and green (grounding) conductor on
one side and the black (hot) conductor on the
other side of the outlet box.
The wire connection points should be turned
upward and pushed carefully up into outlet box.
Connect the white (neutral) wire
from motor to the white (neutral)
wire from the outlet box with a
wire connector.
Connect the black (hot) wire from
motor to the black (hot) wire from
outlet box with a wire connector.
Black
Black
White
White
Ground
Ground
231121
1) There are four mounting plate screws and lock washers. Remove two screws
and lock washers from the mounting plate (one from each side) and loosen
the other two remaining screws.
2) Remove the fan motor assembly from the hook of the mounting plate then
align the “L shaped” slots of the fan motor assembly with the two remaining
screws on the mounting plate and push the fan motor assembly upwards to
engage the slots and turn clockwise to lock in place.
3) Tighten the screws and install the other two mounting plate screws and lock
washers into the remaining holes of the fan motor assembly and tighten.
Before installing blades to the motor,
please remove three plastic inserts
first.
Aligning the slots of the fan motor
assembly with the studs on the
trim ring, then push the trim ring
upwards to lock in place.
Insert the fan blade through the slot
on the fan motor assembly and
fasten fan blade to the fan motor
assembly with washers and screws.
Repeat for remaining fan blades.
Remove one screw and loosen another two screws
from fan motor assembly first, then thread the fan
motor assembly wires through light kit pan, then
push the light kit pan upwards until the fan motor
assembly screws insert into the key hole slots of
light kit pan, then rotate the light kit pan until it's
fixed on the fan motor assembly bottom. Finally,
secure the light kit pan to the fan motor assembly
bottom with previous screw which was removed.
Tighten the other two fan motor assembly screws.
Fig.13
Slot
Stud
Light Kit Pan
Glass Shade
Remove one screw (for later use) and loosen another two
screws from light kit pan first, then connect the white
(neutral) wire from fan motor assembly to the white (neutral)
wire from the LED module assembly and connect the blue
(hot) wire from fan motor assembly to the blue (hot) wire
from LED module assembly. Carefully put the wires into the
light kit pan. Finally, secure the LED module assembly into
the light kit pan with the previous screw which was removed
and tighten the two loosened screws.
Attach the glass shade to light kit pan by aligning studs and slots, and turn it
clockwise until it is locked in place.
PAGE: 6 / 8
Fan Motor Assembly
Plastic
Insert
Fig.9
Mounting Plate
Mounting Screw
Fan Motor Assembly
Fig.7
Trim Ring
Fan Motor
Assembly
Blade Screw
Fan Blade
Slot
Fig.10
Washer
Fig.11
Fix Screw
Light Kit Pan
Fan Motor
Assembly
Fig.12
Fix Screw
Fan Motor
Assembly
LED Module
Assembly
Light Kit Pan
Fig.8
Trim Ring
Fan Motor Assembly
Stud
Slot
231121
Fig.14
HI
MED
LIGHT ON/OFF
REVERSE
DIMMER
FAN OFF
LOW
TIMER
2H 4H 8H
* Press "HI" button to turn on the fan at high speed.
* Press "MED" button to turn the fan in medium speed.
* Press "LOW" button to turn the fan in low speed.
* Press "FAN OFF" button to turn off the fan.
* Press "REVERSE" button to set direction of fan rotation.
The fan speed will slow down until the fan is turned off and it will restart by spinning
in the reverse direction and resume the previously selected speed setting.
Operating transmitter:
* Press "LIGHT ON /OFF" button to turn on or turn off the light.
* Press and hold the "DIMMER" button to dim or brighten lights to the desired level and
release, and the brightness level will be memorized. Turn on the light again, then fan
light will be restored to the brightness-level at which it was dimmed last time.
* Press "DIMMER" button to change color temperature of fan light. There are a total
of 5 levels of color changing from 2700K, 3000K, 3500K, 4000K to 5000K.
* Timer Control:
Press "2H","4H" or "8H" "Timer" button can be set to automatically turn off the fan and
the light. If the light is off and the fan in on, the timer can automatically turn the fan off
in the selected timer time. (Same goes for the light.)
Press light off or fan off button to stop the timer control and the light or fan will be turn
off at the same time.
Note:
This remote controller has a memory function setting. The fan will operate at the same speed and the fan light will
stay at the same brightness-level as the last time the power supply was turned off.
Set the code:
Within the 10 second time frame after the main power is turned on, press and hold FAN OFF button for more than 3 seconds.
The LED light will begin to flash. Once the code is set successfully, the fan will turn off and the light will turn on.
Note: The included transmitter was paired with the receiver at the factory with default settings, so no need to set
the code again. Go through these setup steps if you found your transmitter can’t communicate with the
receiver.
Install the transmitter wall bracket on the wall with two screws
and place transmitter in it carefully.
Transmitter
Wall Bracket
Screw
15
2H 4H 8H
PAGE: 7 / 8
231121
PAGE: 8 / 8
Troubleshooting Guide
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation
or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any
faults, please check this Troubleshooting Guide. If a problem cannot be remedied or you are
experiencing difficulty in installation, please call our Customer Service Department (1-800-887-6326).
PROBLEM
1. If fan does not start:
2. If fan sounds noisy:
3. If fan wobbles:
4. If light does not work:
5. If fan and light kit do
not work:
1. Check main and branch circuit fuses or circuit breakers.
2. Check line wire connections to fan and switch wire connections in switch
housing.
CAUTION: Make sure main power is turned off.
3. Make sure that the wall control is turned "ON".
1. Make sure all screws in motor housing are snug. (not too tight)
2. Make sure the screws which attach the fan blade bracket to the motor are tight.
3. Make sure wire connectors in switch housing are not rattling against each
other or against the interior wall of the switch housing.
CAUTION: Make sure main power is turned off before accessing switch
housing.
4. Some fan motors are sensitive to signals from Solid State variable speed
controls. DO NOT USE a Solid State variable speed control.
5. Allow "break-in" period of 24 hours. Most noises associated with a new fan will
disappear after this period.
All blades are weighed and grouped by weight. Natural woods vary in density
which could cause the fan to wobble even though all blades are weight-matched.
The following procedures should eliminate most of the wobble. Check for wobble
after each step.
1. Check that all blades are screwed firmly into blade brackets.
2. Check that all blade brackets are tightened securely to motor.
3. Make sure that canopy and mounting bracket are tightened securely to ceiling
junction box and junction box is mounted firmly to ceiling joist.
4. Most fan wobble problems are caused when blades are not equally level. To
check the blade levels, select a point on the ceiling above the tip of any blade.
Measure the distance from the ceiling to the blade tip, to an accuracy of 1/8
inch. Rotate the blades until the next blade is in the measuring position. Repeat
measurement for each blade. If all blade levels are not equal, you can adjust
blade levels by the following procedure. To adjust a blade tip down, insert a
washer (not supplied) between the blade and blade bracket at the screw
closest to the motor. To adjust a blade tip up, insert washer (not supplied)
between the blade and blade bracket at the two screws farthest from the motor.
5. If blade wobble is still noticeable, interchanging two adjacent (side by side)
blades can redistribute the weight and possibly result in smoother operation.
1. Check blue wire from fan to make sure it is connected to hot wire from house.
2. Check for loose or disconnected wires in fan switch housing.
3. Check for loose or disconnected wires in light kit.
4. Check for faulty the LED module.
CAUTION: Make sure main power is turned off before accessing switch
housing.
SUGGESTED REMEDY
1. Replace the battery of transmitter.
2. Re-pair the transmitter and receiver by holding the "FAN OFF" button on the
transmitter according to the manual.
231121
