Loading ...
Loading ...
Loading ...
if a problem should arise, first check the following:
1. Are the connections correct?
2. is the set being operated as described in the owner's manual?
3. Are the other components operating properly?
If this unit does not operate properly, check the items listed in the table below. Should the problem persist,
there may be a malfunction.
In this case, disconnect the power immediately and contact your store of purchase.
[General]
o External noise or interference is o Reset the microprocessor. 41
causing the set to malfunction.
* Connection of the power cord is * Check the insertion of the power 15
faulty, cord plug.
* Check the connections. 9 ~ 15
Set does not
operate properly.
Power does not
turn on, or turns
off directly after it
was turned on.
No sound is
produced from
speakers.
oConnection with the input
devices or connection of the
speaker cables is faulty.
o Device you want to play and set
input source do not match.
oMaster volume is turned too
low.
o Mute mode is set.
o Headphones are connected.
o No digital signals are being
input.
oSelect an appropriate input
source.
* Adjust the master volume to an
appropriate level.
* Cancel the mute mode.
* Disconnect the headphones.
* Select an input source for which
the digital input setting has been
made.
* Set the input mode.
34
35
35
35
24
o The connectors to which the
digital inputs are assigned and
the settable input modes do not
match.
o The Dimmer setting is set to
"OFF'.'
o DVD player's digital audio output
setting is not proper.
34
Display is off. 35
"DOLBY DIGITAL'
indicator does not
appear on display.
9
o Set to something other than
"OFF"
o Check the DVD player's audio
output setting. For details, read
the DVD player's operating
instructions.
o Please switch off power at once,
and re-apply the power after
the body temperature has fallen
sufficiently.
o Please re-install AVR-589 in a
place having good ventilation.
o The protection circuit will be
activated depending upon the
temperature rise in the internal
parts of the unit.
Power switches
off suddenly
while you are
using the AVR-
589, the power
indicator will flash
in red at intervals
of approximately
2 seconds.
_J_!_!_!_!_!_!!}!!i_!i_!!_;;_!_!_!_i_!_i_!_i_!_!_!_!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i_!_!_i_i_i_!:!_!_i_ii_ii_ii_ii_ii_ii_i!i!_i_i!_ii_ii_ii_i!i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_iiii_i_i_i_i_!_!i!i!i!ii!ii!ii!iiiiiiiiiiiiiiiii_iiiiiiiiiiiiiiiiiiiiiiiiii_ii_iiii_i_i_i_;_i_i_!_!_!_!_!_!_!_!_!_!_!_i_i!!!!_i!_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_ii_ii_iiiiiiiiii!i!!_!_i!!i!!i!_i_!i_!i_!i_i_iii!_!_i_i!i_i_i_i_i_i_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_i_i_i!
Power switches
off suddenly while
you are using
the AVR-589, the
sower indicator
will flash red
at intervals of
approximately 0.5
seconds.
Even applying
power, the power
display flashes
red at intervals of
approximately 0.5
seconds.
o Use speakers having impedance
less than that specified.
o If speaker cable core wires touch
each other or the core wires
become disconnected from their
terminals, the protection circuit
will be activated in the event of
core wires coming into contact
with the AVR-589 rear panel.
The AVR-589 amplifier circuit has
failed.
Please use speakers which have 9
the specified impedance.
o Unplug the power cord, then 9
after twisting the core wires
together tightly again, or effecting
termination treatments etc,
please reconnect once again.
Switch off the power and please
contact the DENON service
adviser.
Remote Control Unit]
Set does not work
properly when
remote control
unit operated.
Batteries are worn.
You are operating outside of the
specified range.
Obstacle between main unit and
remote control unit.
The batteries are not inserted in
the proper direction, as indicated
by the polarity marks in the
battery compartment.
The set's remote control sensor
is exposed to strong light (direct
sunlight, inverter type fluorescent
bulb light, etc.).
The remote ID of the main unit
and remote control unit do not
match.
The SOURCE CONTROL switches
are not set in the correct
positions.
_!_!_i_ii_ii_ii_ii_Siiiiii_ii_ii_iii_ii_i_iiiiiiiiiiiiiiiiiiiiiiiiiiii_i_iii_i_!!!!_i_i!ii_ii_iiii!_!!_i_i_i_!_i_!_!!_i_i_i_i_i_i_i_!__!_!!i_!!_!!_!!_!!_!!_!!_!!_!!_!!_!!_!!_!!_!!_!!_!!_!!_!!_!!_!!_!!_!!_!!_!!_!_i!_!
Replace with new batteries.
Operate within the specified
range.
Remove the obstacle.
Insert the batteries in the
proper direction, following the
polarity marks in the battery
compartment.
Move the set to a place in which
the remote control sensor will
not be exposed to strong light.
=Set "Remote ID" for the main
unit to "1 ".
oSet the SOURCECONTROL
switches to the correct positions
according the operation you are
applying.
3
3
3
3
26
36 ~ 38,
42 ~ 44
©
©
£
S
©
50
Loading ...
Loading ...
Loading ...