Loading ...
Loading ...
Loading ...
i
o i
©
2
5'
©
° i
.................................i
U_
_=J SW ATT (Subwoofer Attenuation)
Attenuate subwoofer level when using EXT IN mode.
[Seiectable items]
: The input from the subwoofer channel is attenuated.
• The input from the subwoofer channel is not attenuated.
Usually use in this mode.
Set this to "ON" if the subweefer channel level seems tee high when
playing audio signal.
Subwoofer
Turn subwoofer output on and off.
[SelectabJe items]
• The subwoofer is used.
The subwoofer is not used.
Tone Control
Turn tone adjustments on and off.
[SelectabJe items]
Allowtoneadjustment/treNe,bass/.
P,aybackwithouttoneadjustment.
The tone cannot be adjusted when in the DIRECT mode.
When the "Dynamic EQ" setting is "ON;' setting is not possible.
Bass
Adjust low frequency range (bass).
va.ab eran e -
Treble
Adjust high frequency range (treble).
Va.a Iera. e -
MultEQ
Select the type of room correction desired from the following list:
[Selectable items]
Optimize frequency response of all speakers.
Opt,m,zefrequencyresponseofspeakersexceptfront
L and R speakers.
Optimize frequency response of all speakers to flat
response.
Turnequalizeroff
=- Audyssey Audyssey Byp. L/R
]
OFF _ =- Audyssey Flat
Operating from the main unit or remote control
unit
Press MULTEQ
When "Audyssey', "Audyssey Byp. L/R" or "Audyssey Flat" is
selected, the Audyssey MultEQ indicator lights green.
*After running Auto Setup, if the Speaker Configuration, Distance,
Channel Level and Crossover Frequency have changed without
increasing the number of speakers measured, the Audyssey MultEQ
indicator lights red.
* "MultEQ" can only be set when Auto Setup has been performed.
* "MultEQ" cannot be set in the following situations.
, If "Auto Setup" fails to be completed.
, After running Auto Setup, when the number of used speakers has
increased from the number of measured speakers.
If the settings of speakers for which "None" has been determined
at "Auto Setup" are changed, "Audyssey',' "Audyssey Byp. L/R" and
"Audyssey Flat" cannot be selected. Either perform Auto Setup
again, or return to the setting after running Auto Setup with "System
Setup" - "Spea ker Setup" - "Restore".
When using headphones, "MultEQ" is set to "OFF".
_namic EQ
Audyssey Dynamic EQ solves the problem of deteriorating sound
quality as volume is decreased by taking into account human perception
and room acoustics. Audyssey Dynamic EQ works in tandem with
Audyssey MultEQ to provide well-balanced sound for every listener
at any volume level.
"Dynamic EQ" can only be set when auto setup has been
performed.
"Dynamic EQ" cannot be set in the following situations.
, If "Auto Setup" fails to be completed.
, After running Auto Setup, when the number of used speakers has
increased from the number of measured speakers.
When "MultEQ" is set to "OFF',' "Dynamic EQ" is automatically set
to "OFF".
"Night Mode" and "Tone Control" cannot be used jointly.
[SelectabJe items]
: Use Dynamic EQ function.
Do not use Dynamic EQ function.
Operating from the unit or remote control
unit
Press<DYNVOL>or[DYNAMICVOLUME].
DynamicEQ/V01ume: ON _ DynamicEQ: ON/V01ume: OFF
DynamicEQ/V01ume: OFF _
Before running Auto Setup and after running Auto Setup, if the number
of speakers has increased or you pressed <DYN VOL> or [DYNAMIC
VOLUME], "Run Audyssey" is displayed. In this case, either perform
Auto Setup again, or return to the setting after running Auto Setup with
"System Setup" - "Speaker Setup" - "Restore".
_Operating conditions for each function
Dynamic EQ : When "MultEQ" is set to "ON"
Dynamic Volume : When "Dynamic EQ" is set to "ON"
o DV setting : When "Dynamic Volume" is set to "ON"
"Bass" and "Treble" can be set when "Tone Control" is set to "ON".
31 [For details on adjusting individual parameters, see "Adjusting the Parameters" (_:5_page 29). J
Loading ...
Loading ...
Loading ...