Loading ...
Loading ...
Loading ...
7
ASSEMBLY
NOTE: This Operator’s Manual covers several models. Features may vary by model. Not all
features in this manual are applicable to all models and the model depicted may differ
from yours.
Note: All references in this manual to the left or right side and front or back of the
tractor are from the operating position only. Exceptions, if any, will be specified.
Refer to Figure 1 to match your transmission style; Foot Control CVT (Continuously Variable
Transmission) or CVT, or Hydrostatic.
Manually Moving the Tractor
Hydrostatic Models (If Equipped)
1. Remove parking brake if activated.
2. Engage the transmission bypass rod to move the tractor manually without starting
it. The transmission bypass rod is located on the rear of the tractor, on the frame.
Engage the bypass rod by pulling out and down. See Figure 2.
NOTE: If the tractor will not move or
does not move freely when pushing
check if the hydrostatic bypass rod is
fully open or the brake is engaged.
NOTE: The transmission will NOT engage
when the hydrostatic bypass rod is pulled
out. Return the rod to its disengaged
position prior to operating the tractor.
3. Disengage the transmission bypass rod
by pushing the rod back in after moving
the tractor.
CVT or Foot Control CVT Models (If Equipped)
1. Remove Parking Brake, if activated
2. Place the shift lever in the NEUTRAL (N) position.
Install Operator’s Seat (If necessary)
Knob Adjust or Bolt Adjust
NOTE: The seat is shipped fastened to the tractor
seat’s pivot bracket with a cable tie OR mounted
backward to the pivot bracket. To install the seat
proceed as follows:
1. Remove the seat from its shipping position.
2. Remove the seat adjustment knob or 9/16”
bolt (a) from the bottom of the seat (b). See
Figure 3.
3. Align the seat (b) over the seat pivot bracket
(c) as shown in Figure 3 and fit the seat (b) onto the seat pivot bracket (c) inserting
the two tabs on the seat (b) bottom into the wide opening of the slots on the seat
pivot bracket (c).
Foot Control CVT
CVT
Hydrostatic
Figure 1
Figure 2
(a)
(b)
(c)
Figure 3
4. Slide the seat (b) rearward in the seat pivot
bracket (c), lining up one of the slots in
the seat pivot bracket (c) with the hole in
the center rear of the seat (b) base. See
Figure 4.
NOTE: Be certain the two seat tabs engage
the seat pivot bracket as shown in the
bottom right inset of Figure 4.
5. Select the desired position for the seat (b),
and secure with the adjustment knob or
9/16” bolt (a) removed in Step 2.
Lever Adjust
NOTE: The seat is shipped with the seat
switch and seat pan attached.
1. Cut any straps securing the seat
assembly to the tractor. Remove any
packing material.
NOTE: Be careful not to cut the wiring
harness connecting the seat and the
seat switch.
2. Remove the two shoulder bolts (a) and
flange lock nuts (b) in the seat pan as
shown in Figure 5.
3. Rotate the seat into position and slide a
Phillips screwdriver through one of the
seat-securing holes and seat bracket for
alignment.
4. With the previously removed shoulder
bolts (a) and flange lock nuts (b) secure
one side of the seat and seat bracket.
While supporting the seat, remove the
Phillips screwdriver and secure the other
side of the seat. Be careful not to crimp
or damage the wire harness while installing
the seat. See Figure 6. Torque to 84-103
in-lbs (9.5-11.6 N-m).
5. Using the harness clip attached to the
harness, secure the excess wire to the fender
by snapping the harness clip in place as
shown in Figure 7.
Dash Shroud (If Equipped)
1. If the dash shroud (a) was shipped loose,
the hardware for attaching the dash
shroud (a) is shipped attached to the dash
shroud (a). Remove the two bolts (b) from
the dash shroud (a). See Figure 8.
2. Mount the dash shroud (a) and align the
mounting holes between the top of the
dash and the dash shroud. See Figure 8.
3. Secure the dash shroud (a) to the dash (c)
with the bolts (b) removed in Step 1. See
Figure 8.
(b)
(c)
(a)
Figure 4
(a)
(a)
(b)
(b)
Figure 5
(a)
(b)
(a)
(b)
Figure 6
Figure 7
(b)
(a)
(c)
(a)
(b)
Figure 8
Loading ...
Loading ...
Loading ...