Loading ...
Loading ...
Loading ...
OPERATION
10
Note: This Operator’s Manual covers several models. Tractor features may vary by
model. Not all features in this manual are applicable to all tractor models and the
tractor model depicted may differ from yours.
NOTE: References to LEFT, RIGHT, FRONT, and REAR indicate that position on the riding
mower when facing forward while seated in the operator’s seat.
1
Drive Pedal (Foot Control CVT Models)(If Equipped)
Depress the drive pedal forward to allow the tractor to travel. The further forward the
pedal is depressed, the faster the tractor will travel. The pedal will return to its original/
neutral position when it’s not depressed.
2
Speed Control Lever (Hydrostatic Models)
To drive forward or in reverse, slowly move the speed control
lever to the desired “F” forward or “R” reverse speed.
To stop, move the speed control lever to the “N” neutral position.
When mowing, place the speed control lever in the “Cutting
Speed” position, or a slower forward speed for the best results.
NOTE: Do NOT use the parking brake pedal to control the
ground speed of the tractor while driving. Always use the
speed control lever to slow the ground speed of the tractor.
Depressing the parking brake pedal with the speed control
lever engaged as part of regular operation will result in
premature wear of the drive belt.
IMPORTANT: Do
NOT attempt to change the direction of travel when
the tractor is in motion. Serious damage to the tractor’s transmission
could result. Always bring the tractor to a complete stop before
moving the speed control lever from forward to reverse or vice versa.
3
Shift Lever
(CVT & Foot Control CVT Models)
The shift lever is located on
the left side of the fender and
has three positions; FORWARD
(F), NEUTRAL (N) and REVERSE
(R). The brake pedal must be
depressed and the tractor must
not be in motion when moving
the shift lever.
IMPORTANT: Never force
the shift lever. Doing so may
result in serious damage to the
tractor’s transmission.
4
Brake Pedal/ Clutch-Brake Pedal
Depress the brake pedal/ clutch-brake pedal while the tractor is in use
to stop the tractor, to shift (CVT and Foot Control CVT models) and for
setting the parking brake.
Note: The brake pedal/ clutch-brake pedal must be fully depressed
to start the tractor. Refer to Safety Interlock System for more
information.
5
Throttle or Throttle/Choke Control Lever
Some models have an auto-choke feature. These models do not come with a manual
choke function. Push the throttle or throttle/choke control lever forward to increase the
engine speed. The tractor is designed to operate with the throttle/choke control lever at
full throttle (FAST) when the tractor is being driven and the mower deck is engaged. Pull
the throttle/choke control lever rearward to decrease the engine speed. When starting the
engine, if equipped with a throttle/choke control lever, push the control lever fully forward
into the “CHOKE” position. After starting and warming the engine, move the control lever
rearward until you feel it move past the choke detent. Throttle is not meant to control unit
speed, throttle should remain in high speed while operating blades.
6
Deck Lift Lever
The deck lift lever is used to raise and lower the deck. Pull the lever to the left out of the
index notch and push downward to lower the deck, or pull upward to raise the deck.
When the desired height is attained, move the lift lever to the right until fully engaged
in the index notch.
7
Ignition Switch
WARNING
Never leave a running tractor unattended.
Always disengage PTO, set parking brake, stop
engine and remove key to prevent unintended
starting.
Refer to Starting the Engine for information on how
to start the engine. Refer to Stopping the Engine for
instructions on how to stop the engine.
Figure 18
1
2
3
4
5
6
7
8
9
10
11
Loading ...
Loading ...
Loading ...