Loading ...
Loading ...
Loading ...
motor specifications and eledricat requirements
This machine ;s designed to use a 34,50 RPM motor only.
Do not use any motor that runs faster than 3450 RPM.
It {s wired for operation on 110420 volts, 60 Hz, aite__
nating current, iT MUST NOT BE CONVERTED TO
OPERATE ON 230 VOLTS_ EVEN THOUGH SOME OF
THE RECOMMENDED MOTORS ARE DUAL VOLTAGE.
THESE CRAFTSMAN MOTORS HAVE BEEN
FOUND TO BE ACCEPTABLE FOR USE ON
THIS TOOL,
t/2 3450 110. t20 1216
t/2 3450 110-120 1218
3/4 3450 1!0-120 1219
3/4 3450 11O,120 1226
CAUTION: Do not use blower or washing machine motors
or any motor with an automatic reset overload protector
as their use may be hazardous,
CONNECTING TO POWER SOURCE OUTLET
This machine must be grounded while in use to protect
the operator from electric shock.
Plug power cord into a 110.120V properiy grounded type
out_et protected by a 15_amp. dual element time delay or
Circuit.Saver fuse or circuit breaker,
If you are not sure that your outlet is properly grounded,
have it checked by a qualified electrician,
WARNING: DO NOT PERMIT FINGERS TO TOUCH THE
TERMINALS OF PLUGS WHEN INSTALLING OR RE-
MOVING THE PLUG TO OR FROM THE OUTLET.
WARNING: IF NOT PROPERLY GROUNDED THIS
POWER TOOL CAN INCUR THE POTENTIAL HAZARD
OF ELECTRICAL SHOCK. PARTICULARLY WHEN USED
IN DAMP LOCATIONS IN PROXIMITY TO PLUMBING.
IF AN ELECTRICAL SHOCK OCCURS THERE IS THE
POTENTIAL OF A SECONDARY HAZARD SUCH AS
YOUR HANDS CONTACTING THE ABRASIVE BELT
OR DISC.
tf power cord is worn or cut, or damaged inany wav, have
it replaced immediately.
If your unit is for use on less than 150 volts it has a plug
that looks like below.
3-PRONG
PLUG
GROUNDING
PRONG
This power tool i_ eqLJipped with a 3.conductor cold and
groundmg tV_; _))Ug which has a grounding prong, _pp_oved
by Underwriters' Labora!or}es arid the Canadian Standards
As'¢ociation. The ground conductor has a green ie..¢ket and
is attached to the toot housing at on_ end af_d to the ground
prong in the attachmer_t plt,g at the Other end.
This plug requires a mating 3-conducto. _ grounded type
outlast as shown.
If the outtet yot_ are planning to use for this power tooi is
o¢ the two prong tYi:_ DO NOT REMOVE OR ALTER
THE GROUNDING PRONG IN ANY MANNER. Use an
adapter as shown and always connect the grounding )ug tO
known gro_and,
It is recommended tha! you have a qualified eiectrician
replace the TWO prong outlet with a proper!*,, grounded
THREE prong OUtlet,
An adapter as shown tx.qow is available for cOnr'ecting plugs
to 2-prong receptacie, s. The green gr'oundmg_t_g extending
from the adapter must be connected to a permanent ground
slach a,_ to a proL,_erly grounded outlet box.
NOTE: The adapter illustrated is for use on}y }f you already
have a properly grounded 2-prong receptacie. Adapter is
not allowed in Canada by the Canadian Efectricat Code.
The use of any extension cord wili cause son_ loss of
power. To keep this to a minimum and to prevent over-
heating and motor burn-out, use the table below to deter-
mine the minimum wire size (A.W.G.) extension cord, Use
only 3 wire extenSiOn cords which have 3.prong grounding
type plugs and 3-poie receptacles which accept the _oo}s
plug.
Extension Co_d Length Wire Size A.W.G,
Up to t00 Ft. t6
I00,200 Ft, 14
200- 400 Ft. !0
CHECK MOTOR ROTATION
WARNING: FOR YOUR OWN SAFETY, MAKE SURE
PLUG IS NOT CONNECTED TO POWER SOURCE OUT-
LET. WHEN CHANGING MOTOR ROTATION.
The motor must rotate COUNTERCLOCKWISE when
viewed from the shaft end to which you w_{{ n'_Ount th_
pulley, [See page tt) H it does not, change the d:_ec-_io_
according to the instructions furnished with the ,q_Ot_:_r
5
Loading ...
Loading ...
Loading ...