Loading ...
Loading ...
Loading ...
En
26
Changing the settings
Launching utilities mode
If utilities mode is launched while the unit and a computer are con-
nected by a USB cable, the set status may not be displayed properly.
The “MIDI Controller Settings” can be set in the utilities mode.
This unit automatically switches operation as shown below depending
on whether or not rekordbox dj is running.
!
When rekordbox is running, controller operation depends on the
rekordbox dj functions.
!
When rekordbox dj is not running, this controller operates as a gen-
eral MIDI controller.
Even if rekordbox dj is running, this controller can forcibly be operated
as a general MIDI controller.
1 Disconnect the USB cable from the computer.
2 Press the [u] switch on the rear panel of this unit to
set the unit to standby.
This unit enters standby mode.
3 While pressing both the [SHIFT] and
[PLAY/PAUSE f] buttons on the left deck, press the
[u] switch on the rear panel of this unit.
Utilities mode is launched.
4 Press the [SLIP REVERSE] button on the left deck.
! [SLIP REVERSE] button (not lit): Automatically switches operation
depending on whether or not rekordbox is running.
! [SLIP REVERSE] button (lit): Forcibly operates as a general MIDI
controller regardless of whether or not rekordbox is running.
5 Press the [u] switch on the rear panel of this unit to
set the unit to standby.
To save the settings, set the [u] switch on the rear panel of this unit to
standby and quit utilities mode.
Changing the settings with
rekordbox
The settings required for the DJ player can be changed with rekordbox.
Change the setting items in [Controller] of [Preferences].
! The following settings can be changed only when rekordbox and this
unit are connected.
Setting items in the [Deck] tab of
[Controller]
Ring Brightness setting
Sets the brightness of the JOG RING illumination.
You can switch the setting from a level of 1 to 3. The jog ring does not
illuminate when set to Off.
!
Set to 1 for the darkest illumination, and 3 for the brightest
illumination.
Jog > Brightness of the display setting
Sets the brightness of the jog display section.
5 levels from 1 to 5 are available for this setting.
! Set to 1 for the darkest illumination, and 5 for the brightest
illumination.
Display setting for the jog display
You can change the information displayed in the jog display section.
Display Artwork
When the [Display Artwork] check box is selected, the display is
enabled and the artwork for the track loaded from rekordbox is displayed
on the jog display.
Display CUE SCOPE
When the [Display CUE SCOPE] check box is selected, the display is
enabled and the CUE SCOPE is displayed on the jog display.
Time Mode
The information displayed for the time display can be switched with
[Time Mode].
! Elapsed: With 0:00 as the starting point of the track, displays the
time elapsed from the beginning to the current playback position.
! Remaining: With 0:00 as the end of the track, displays the time
remaining to the end from the current playback position.
Slip Mode Flashing
Changes the slip mode flashing setting.
— Enable: The buttons that can be operated only while slip mode is
on flash (the [HOT CUE] button, the [4 BEAT LOOP/EXIT] button,
etc.).
— Disable: The buttons that can be operated only while slip mode is
on do not flash.
Slip button LED while slip mode is on
Sets the lighting operation of the [SLIP] button for when slip mode is on.
— Light is On: The [SLIP] button lights up when slip mode is on,
and flashes while slip mode is being operated.
— Blink: The [SLIP] button does not light up when slip mode is on.
Setting items in the [Mixer] tab of
[Controller]
Fader Start setting
Changes the fader start function setting.
! By default, this is enabled.
When the [Activate the fader start when moving a channel fader
or the cross fader while pressing the SHIFT button.] check box is
selected, the function is enabled.
Cross Fader Curve setting
Switches the characteristics of the crossfader curve.
! The further the control is turned clockwise, the sharper the curve
rises.
! The further the control is turned counterclockwise, the more gradu-
ally the curve rises.
Cross Fader Cut Lag setting
Adjust the play (cut lag) of both ends of the crossfader.
Adjustment can be made from 0.3 mm to 5.5 mm in 0.1 mm increments.
! By default, the level is set to 1.0 mm.
Loading ...
Loading ...
Loading ...