Loading ...
Loading ...
Loading ...
19
Your McIntosh MAC7200 has been factory config-
ured to allow immediate enjoyment of superb audio
without the need for further adjustments. If you wish
to make changes to the factory default settings, a
Setup Feature is provided to customize the operating
settings using the Front Panel Information Display.
Refer to the MAC7200 Front Panel Illustration on the
previous page while performing the following steps.
Note: If the MAC7200 is currently On, proceed to
step 2.
1. Press the STANDBY/ON Push-button on the Front
Panel or press the (Power ON) Push-button on
the Remote Control to switch On the MAC7200.
The MAC7200 will go through a brief startup
initialization with the Front Panel Information
Display first indicating “MAC7200”, followed by
the last used source and volume setting. This is
followed by the volume setting indication starting
at zero and then increasing to the last used volume
setting. Refer to figure 1.
2. Press and hold in the INPUT Control until
the Front Panel Information Display indicates
“MAC7200 V1.00, (or higher Main Firmware
version) - S/N: AFN____” (Serial Number).
Refer to figure 2.
3. Rotate the INPUT Control to select the Setup
Mode Menu item, “SETUP: Inputs, (Hold IN-
PUT)”. Refer to figure 3.
Continue to rotate the INPUT CONTROL to view
the other SETUP Mode Options.
4. To exit from the SETUP Mode, press and hold in
the INPUT Control and the Front Panel Display
will indicate its normal display. Refer to figure 1.
The MAC7200 functionality is controlled by internal
software that is know as Firmware. There are three
Firmware Identification Numbers for the MAC7200.
The first Firmware Number is for the Main Circuitry
of the MAC7200 and can be identified at any time by
utilizing the Setup Mode.
1. Press and hold in the INPUT Control to enter
Setup Mode.
2. Referring to the Front Panel Information Display-
the number after the character “V” is the Firm-
ware number. Refer to figure 2.
To view the second Firmware Number (the Digital
Audio Circuitry of the MAC7200) or the third Firm-
ware Number (the Tuner Circuitry of the MAC7200),
perform the following steps:
3. Press and hold in the INPUT Control to enter
Setup Mode.
4. Rotate the INPUT Control until the Front Panel
Information Display indicates “DA1 Firmware,
V1.00” (or higher Digital Audio Firmware ver-
sion). Refer to figure 4.
4. Rotate the INPUT Control until the Front Panel
Information Display indicates “TUNER FIRM-
WARE Firmware, V1.00” (or higher Digital
Audio Firmware version). Refer to figure 5.
5. To exit the Setup Mode, press the INPUT Control.
How to Operate the Setup Mode
The Default Settings Chart below indicates the Func-
tion Name, Default Setting and the Page Number for
additional information.
Default Settings
Firmware Version
Default Settings
Function Name Setting Page No.
MAC7200 V_._ _ 19
DA1 V_._ _ 19
TUNER FIRMWARE TM________ 19
INPUTS On / Rename 20
OUTPUTS (1 & 2) Switched 20
TRIGGER 1 Output 1 20
TRIGGER 2 Output 2 20
DATA PORTS
(1 thru 4)
All Data 20
PASSTHRU OFF 21
USB Automute ON 21
RS232 (Rate) 115200 Baud 21
Remote Control Codes Normal 21
IR Sensor Enabled 22
Power Mode Enabled 22
Tune r Presets --- 25
Tune r Reg ion USA 26
Setup
Figure 2
MAC7200 V1.00
S/N: AFN____
Figure 1
BAL
15%
Figure 3
SETUP: Inputs
(Hold INPUT)
Figure 4
DA1 FIRMWARE
V1.00
Figure 5
TUNER FIRMWARE
TM30104101
Loading ...
Loading ...
Loading ...