Loading ...
Loading ...
Loading ...
TroubleshootingInformationHDMI Control FunctionPlaybackConnectionsGetting Started Specications
ENGLISH
26
Setting items
Setting contents
7.1-ch Audio Out
NOTE
• Select “Large” or “Small” not according to the physical size of the
speaker but according to the low frequency reproduction capabilities
based on the frequency set at “Crossover Freq.”.
• On the GUI menu, if the “Audio Setup” – “7.1-ch Audio Out”– “Multi
Channel” – “Speaker Conguration” item setting is changed, other
settings are automatically changed as well.
GExampleH
If you set “Front” to “Small”, “Subwoofer” is set to “Yes” and “Large”
cannot be selected for “Center”, “Surround” and “Surr. Back”.
• Audio signal (sampling frequency, number of channels) from the
HDMI output terminal may be restricted by the specication of the
HDMI audio that can be input by the device on the other side.
GExampleH
If the HDMI audio specication of the device on the other side
is 5.1-channel, even when DBP-A100 plays back in 7.1-channel,
5.1-channel audio is output automatically. In that case, the analog
audio output becomes 5.1-channel output as well.
n Channel Level : Sets the volume of the test tone to be the same when
output from each speaker.
GModeH : Select a test tone output method.
• Auto : Automatically switches the test tone output speaker.
• Manual : Manually switches the test tone output speaker.
GStartH : Begins outputting the test tone.
Front L / Center / Front R / Surround R /
Surr. Back R / Surr. Back L / Surround L / Subwoofer
b When the test tone output stops, press
.
GSW +10dBH : Increases the subwoofer output level by 10 dB.
z
• Off : Does not change the subwoofer output level.
• On : Increases the subwoofer output level by +10 dB.
z : “SW +10dB” cannot be set for “HDMI Setup” – “Audio Setup” –
“Multi LPCM BM On” – “Channel Level” on the GUI menu.
GDefaultH : Resets all channel level settings to factory default.
• No : Does not Reset.
• Yes : Resets.
Audio Setup
Setting items
Setting contents
7.1ch Audio Out
n Distance : Sets the distance between the listening position and each
speaker.
GFeetH or GMetersH : Set the unit of distance.
GStepH : Set the minimum variable width of the distance.
1ft, 0.1ft, 0.1m, 0.01m
GDefaultH : Reset all distance settings to factory default.
Front L / Front R / Center / Subwoofer / Surround L / Surround R /
Surr. Back L / Surr. Back R : Select the speaker you want to set, and
set the distance. Set the value that is closest to the measured distance.
0 ~ 60ft or 0 ~ 18m
• Default settings :
Front/Center/Subwoofer : 12 feet (3.6 meters)
Surround/Surr. Back : 10 feet (3.0 meters)
• Set the difference in the distance betweem the speakers to less than
20 feet (6.0 meters).
NOTE
When “BD Audio Mode” is set to “HD Audio Output” (vpage 32), the
“Distance” setting is disabled during DTS-HD 192kHz audio playback.
Subwoofer Mode
Sets the type of low
frequency signal to be
output from the subwoofer.
LFE : Adds the low frequency signal of the channel for which the speaker
size is set to “small” to the subwoofer signal and outputs it.
LFE+Main : Adds the low frequency signal of all channels to the
subwoofer signal and outputs it.
Remote control operation
buttons
:
Displays the menu
Cancels the menu
:
Moves the cursor
(Up/Down/Left/Right)
:Makes the setting :Returns to previous menu
Setup
1.DBP-A100_E3_ENG_007.indd 26 2010/08/12 19:20:18
Loading ...
Loading ...
Loading ...