Loading ...
Loading ...
Loading ...
42
Subsequent Cleaning
1.
Open the appliance door and remove the remaining
water with an absorbent sponge cloth.
2.
Clean the smooth surfaces in the oven cavity with a
dish cloth or a soft brush. Stubborn residues can be
removed using a soft scouring pad.
3.
Remove limescale with a cloth soaked in vinegar.
Then wipe with clean water and rub dry with a soft
cloth (including under the door seal).
4.
Turn the function selector to OFF.
5.
Leave the appliance door ajar in the stop position
(approx. 30°) for approx. one hour to allow the enamel
surfaces in the oven cavity to dry thoroughly.
Alternatively, you can also run the Drying function for
the oven cavity.
Running the Drying Function for the Oven Cavity
1.
Turn the function selector to CLEAN MODES.
2.
Swipe to the left or right to select "Drying ª".
3.
Touch the bottom line.
After a few seconds the appliance starts Drying. The
remaining time appears on the display.
As soon as the Drying function has run through, a signal
sounds and the appliance ends the operation
automatically.
Removing Heavy Food Deposits
You have several options for removing particularly
stubborn food deposits.
▯ Leave the vinegar solution to work for some time
before starting Easy Clean.
▯ Rub vinegar solution onto the food and food spills on
the smooth surfaces before starting Easy Clean.
▯ Repeat the Easy Clean function after the oven cavity
has cooled down.
Descale
The appliance must be descaled regularly in order for it
to continue operating correctly.
There are several steps in the descaling program. For
hygiene reasons, the descaling program must be run
through completely so that the appliance can be ready
for operation again. In total, the descaling program runs
for approx. 70-90 minutes.
▯ Descale (approx. 55-70 minutes)
▯ First rinsing cycle (approx. 6-9 minutes)
▯ Second rinsing cycle (approx. 6-9 minutes)
If descaling is interrupted (for example, due to a power
failure or because the appliance is switched off), you are
prompted to rinse the appliance twice after it is switched
back on. The appliance cannot be used until the second
rinsing cycle comes to an end.
The frequency with which the appliance must be
descaled depends on the hardness of the water used.
When only five more steam-assisted operations are
possible, or fewer, the appliance reminds you to descale
it with a message on the display. The number of
remaining operations is displayed after the appliance is
switched on. You can therefore prepare for the descaling
in good time.
Start
NOTICES
▯ Only use the descaler recommended by Thermador
for the descaling program. Other descalers may
damage the appliance.
Descaler order no. 573828
▯ If you have used a steam-assisted operation
immediately before descaling, you must first switch the
appliance off so that the residual water is pumped out
of the evaporator system.
▯ Descaling solution: Do not allow the unmixed
descaling crystals or mixed solution to come into
contact with the control panel or other surfaces on the
appliance as prolonged exposure may cause damage
to the surfaces. Immediately remove any descaler by
rinsing with tap water.
1.
Mix 32 fluid oz. (650 ml) of water with 28 g of descaler
to make a descaling solution to fill the watertank.
2.
Turn the function selector to CLEAN MODES.
3.
Swipe to the left or right to select "Descale ,".
4.
Touch “continue”.
The duration of the descaling program is displayed. It
cannot be changed.
5.
Touch “continue” again.
6.
Remove the water tank and fill it with descaling
solution.
7.
Once the water tank has been filled with descaling
solution, push it back in again fully.
8.
Follow the on-screen instructions.
The appliance will now be descaled. The remaining
time counts down on the display. As soon as the
descaling program has finished, an audible signal
sounds.
Loading ...
Loading ...
Loading ...