Loading ...
Loading ...
Loading ...
• Do not removeor altergroundingpronginany manner.
Inthe eventofa malfunction or breakdown, grounding
providesa pathof leastresistanceforelectricalshock.
WARNING: Do not permitfingers to touchthe termi-
nals of plug when insertingor removingfrom outlet.
• Plug must be plugged into matchingoutlet that is
properly installedand groundedin accordance with
all localcodes and ordinances.Do not modifyplug
provided.If it will not fit in outlet, have proper outlet
installed bya qualified electrician.
• Inspect tool cordsperiodically,and if damaged, have
repaired byan authorized service facility.
• Green (or green and yellow)conductorin cord isthe
groundingwire. If repair or replacement of the elec-
tric cord or plug is necessary,do not connect the
green (or green and yellow)wire to a live terminal.
• A 2-prong wall receptacle mustbe replaced with a
properly grounded3-prong receptacle installedin
accordance with National Electric Code and local
codes and ordinances.
WARNING: Any receptacle replacement shouldbe
performed by a qualified electrician.
A temporary 3-prong to 2-pronggroundingadapter (see
Figure 10) is available for connecting plugs to a two
pole outlet if it isproperly grounded.
GroundingLug _ r==_MakoeSUrc_e'rhis
Adapter IIToAKnown
3-ProngP__.. Ground
"_"--'- _"_2-Prong Receptacle
Figure10 - 2-ProngReceptaclewith Adapter
• Do not use a 3-prong to 2-prong groundingadapter
unless permitted by local and nationalcodes and
ordinances.(A 3-prong to 2-prong groundingadapter
is not permittedin Canada.)
Where a 3-prongto 2-preng groundingadapter is
permitted, the rigidgreen tab or terminal on the side
of the adapter mustbe securely connected to a
permanent electricalground such as a propedy
groundedwater pipe, a propedy groundedoutletbox
or a properlygroundedwire system.
• Many cover plate screws, water pipes and outlet
boxes are not properlygrounded.To ensure proper
ground, groundingmeans mustbe tested bya quali-
fied electrician.
EXTENSION CORDS
• The use of any extensioncord will cause some drop
in voltage and lossof power.
• Wires of the extension cord mustbe of sufficientsize
to carry the currentand maintainadequate voltage.
• The minimumextension cord wire size isA.W.G. 12.
Do not use extension cords over 25 feet long.
• Use only 3-wire extensioncords having3-prong
groundingtype plugs and 3-pole receptacles which
accept the tool plug.
• If the extensioncord isworn, cutor damaged in any
way, replaceit immediately.
Planeris suppliedwith a 3 HP motor installed.
The 120 Volt AC universalmotorhas the following
specifications:
Horsepower (Maximum Developed)............ 3 HP
Voltage................................... 120
Amperes............................ _...... 15
Hertz ..................................... 60
Phase.............................. _... Single
Cutterhead RPM ..................... : .... 5500
ELECTRICAL CONNECTIONS
WARNING: Make sure unitisturned off and discon-
nected from powersource beforeinspectinganywidng.
The motorisinstalledand wiringconnected as illustrat-
ed in thewiringschematic (see Figure 11).
Switch
Cir k_"
MotorHousing
Figure11- WiringSchematic
The motoris assembledwith an approvedthree con-
ductorcordto be used on 120 volts as indicated.The
power supplytothe motoris controlledby a double pole
locking switch. !.
The power linesare connecteddirectlyto the switch.
The green groundlinemust remainsecurel_fastened
to the frame to propedyprotectagainst electricalshock.
A manual resetovedoad protectoris installedin line
with the powersupplytothe motor.If the planer/molder
isoverloaded,the protectorwill break the circuit.
DESCRIPTION
Craftsman15" planer/molderfinishesrough-cutlumber
to size and planessoftand hardwoodsup to 6" thickand
15"wide.Woodfeeds intotwo-blade cutterheadbyrub-
ber infead/outfeedrollers.Sturdybase censtmcUon and
four-post designpermitssmoothfeeding andvirtually
snipelessplaning.Planer/moldercomeswithenclosed,
universalballbeadng,3 HP (max.developed)motorwith
ovedoad protection.Motorhas ON/OFF switchwith
removablekeyto preventaccidentalstart-up.Unitfea-
tures power movementcontrolfor rollercase,depth-of-
cut gaugefor convenient setup,workpiecethid(ness pre-
set gaugewith6 settingsfor consistentsetup,easy
hands-flea replacementof bladesfor safetyand mini-
mizeddowntime,built-indust collector, top mounted
rollersfor workpiecareturn, built-incarryinghandles,
cordwraps forportability and folding infeed/outfeed
tables with rollersfor smoothoperation.Planer/molder
takes cutsupto =A_"per pass at 22 feet per minute.Inch
heightscale hasgraduationsin 'A,"increments,and met-
dcheightscalehas graduationsin lmm Incrslments.
6
Loading ...
Loading ...
Loading ...