Loading ...
Loading ...
Loading ...
15
COUNTERTOP OVERHANG
The control panel is designed to sit flush against the grill enclosure front wall. If the non-combustible enclosure
countertop extends beyond the front wall, creating a countertop overhang, it must be cut flush with the front wall
for the width of the control panel or a gap will be created exposing the forward portions of the left and right side
grill fire walls. See illustrations above.
ENCLOSURE VENTILATION
FOR YOUR SAFETY, you must provide openings in the grill enclosure for replacement air and ventilation (in
case of possible leakage from gas connections or propane cylinders). Failure to do so may result in a fire or
explosion causing property damage, bodily injury, or death. See the GRILL ENCLOSURE / VENTILATION
REQUIREMENTS section for details.
TOP VIEW
Countertop
Countertop
overhang
Control panel
Fig. 15-1
FRONT VIEW
B
C
D
See next page
for substrate
considerations
Countertop
overhang
X
TOP VIEW
SIDE VIEW
Countertop
overhang
(Control
panel)
(Countertop)
Y
1
/
4
"
Clearance
(Overhang)
X= (D-B)÷2
Y= Total
Countertop
Overhang
A
Control
panel
Check clearance for
control panel removal
MODEL SPECIFICATIONS (cont.)
E660i E790i E1060i
A Countertop to unit bottom cutout* 11
1
/2" 11
1
/2" 11
1
/2"
B Side to side non-combustible cutout* 31
1
/4" 37" 50"
C Front to back non-combustible cutout*† 23
1
/2" 23
1
/2" 23
1
/2"
D Control panel width non-combustible cutout‡ 33" 38
3
/4" 51
3
/4"
* Note: If installing this grill in a combustible enclosure, the correct insulating liner must be used. Consult liner instructions for
counter cutout dimensions and installation.
†
Includes any substrate at front wall of enclosure (in the area the rear of the control panel is to sit flush against). See SUBSTRATE
section on next page.
‡
Only applicable for non-combustible enclosures that have countertops with an overhang (see illustration and section below).
Table 3 - Cutout Dimensions
2
3
/4"
2
3
/4"
4"4"
1
1
/2" ø or 1
1
/2"
square hole for
electrical supply
1
1
/2" ø or
1
1
/2" square
hole for gas
supply
Lower
support
NON-COMBUSTIBLE
GRILL ENCLOSURE
CUTOUT DIMENSIONS
TOP VIEW
Countertop
overhang
Fig. 15-1
FRONT VIEW
B
C
D
See next page
for substrate
considerations
Countertop
overhang
X
TOP VIEW
SIDE VIEW
Countertop
overhang
(Control
panel)
(Countertop)
Y
1
/
4
"
Clearance
(Overhang)
X= 1"
Y= Total
Countertop
Overhang
A
Control
panel
Check clearance for
control panel removal
Countertop
Control panel
H790i
A Countertop to unit bottom cutout* 11
1
/2"
B Side to side non-combustible cutout* 37"
C Front to back non-combustible cutout*† 23
1
/2"
D Control panel width non-combustible cutout‡ 38
3
/4"
* Note: If installing this grill in a combustible enclosure, the correct insulating liner must be used. Consult liner instructions for
counter cutout dimensions and installation.
†
Includes any substrate at front wall of enclosure (in the area the rear of the control panel is to sit flush against). See SUBSTRATE
section on next page.
‡
Only applicable for non-combustible enclosures that have countertops with an overhang (see illustration and section below).
2
3
/4"
2
3
/4"
4"4"
1
1
/2" ø or 1
1
/2"
square hole for
electrical supply
1
1
/2" ø or
1
1
/2" square
hole for gas
supply
Lower
support
NON-COMBUSTIBLE
GRILL ENCLOSURE
CUTOUT DIMENSIONS
Loading ...
Loading ...
Loading ...