Loading ...
Loading ...
Loading ...
www.foodsaver.ca 1-877-804-5383
14
www.foodsaver.ca 1-877-804-5383
13
To Clean Appliance:
Press Power Button
9
and remove Power Cord
from electrical outlet. Do not immerse in liquid.
Slide out Drip Tray Drawer (O). Remove Drip Tray
for cleaning by pulling up on the two side tabs.
Check Lower Gasket (N) around Drip Tray (O)
to make sure it is free from food materials.
Do not attempt to remove gaskets.
Antibacterial Drip Tray:
Empty Drip Tray after each use. Wash in warm soapy
water or place in top rack of dishwasher. The Adjustable
Food Sensors in the Drip Tray (O) will not function correctly
if liquid is allowed to remain in Drip Tray.
This appliance has a Tray Full indicator
3
. When excess
liquid fills the Drip Tray, the unit will turn off and the
Tray Full Indicator light will activate. To resume normal
operation, slide out Drip Tray Drawer. Remove Drip Tray
for cleaning by pulling up on the two side tabs. When
replacing drip tray, set the right end of the drip tray into
place, then firmly snap both sides down. Appliance can
be used without Drip Tray, however the Adjustable Food
Sensor setting
7
will not function without the Drip Tray.
Care and Cleaning
CARE & CLEANING
Remove All Food
Around Gaskets
Push In
Tabs
Push In
Tabs
DO NOT
REMOVE
GASKETS
Your FoodSaver
®
Vacuum Sealing System has a special
Quick Marinate Cycle which will last about ten minutes.
The FoodSaver
®
Quick Marinating Canister is the perfect
FoodSaver
®
accessory for marinating foods.
During the Marinate Cycle, the vacuum pump will “hold”
the vacuum for several minutes then release the vacuum,
allowing the food to “rest” for 30 seconds. This process then
repeats. This “pulsing” action of “vacuuming and resting”
will allow for quicker more flavorful marinating.
Important Note: During the Quick Marinate Cycle,
make sure knob on lid of the Quick Marinating Canister
is set to OPEN. Do not set knob to Vacuum during the
Marinate Cycle.
1. Prepare enough of your favorite marinade to fully
cover food inside a marinating canister.
Always leave at least one inch (2.54 centimeters)
of space between contents and top of rim.
2. Make sure rubber gasket underneath lids as well as rim
of marinating canister is free from food materials.
3. Pull out Retractable Handheld Sealer from your
FoodSaver
®
appliance. Remove clear bottom portion of
Retractable Handheld Sealer from top handle (Fig. 1).
4. Insert the end into the port on the canister. Make sure
knob on accessory lid is set to OPEN (Fig. 2).
5. Make sure lid is firmly attached to marinator base.
6. Press Marinate button
2
on the control panel (Fig. 3).
7. Your FoodSaver
®
Vacuum Sealing System will now
begin the Quick Marinate Cycle. The Marinate Indicator
Light will flash to indicate the marinating process has begun.
8. During the initial vacuum cycle the Marinate Mode Indicator
will illuminate. While Marinating, the Vacuum Progress
Display will blink during the Vacuum Hold or Rest Cycle.
9. To preserve food safely, after completing the marinating
cycle, the appliance will signal with short beeps to indicate
your Quick Marinate Cycle is completed. Press any button
to silence the signal. You may now cook or refrigerate your
marinated food.
10. To use the Quick Marinating Canister for extended vacuum
storage (beyond the short Marinate Cycle): Rotate knob to
Vacuum/Canister position, connect the Retractable Handheld
Sealer (as above) and select Accessory Mode
1
from the
control panel. When motor turns off, rotate knob clockwise
to the “Closed” position, then gently twist and remove
Retractable Handheld Sealer from accessory.
Marinating with your FoodSaver
®
Appliance
Fig. 3
2
Fig. 2
HOW TO MARINATE
Fig. 1
1
Slide out drawer to
access Drip Tray
FSFSSL4825-033_13EFM1.indd 13-14 7/23/13 10:07 AM
Loading ...
Loading ...
Loading ...