Loading ...
2
W415-1361 / 11.28.14
EN
TABLE OF CONTENTS
NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.
1.0 INSTALLATION OVERVIEW 3
2.0 INTRODUCTION 4
2.1 DIMENSIONS 5
2.1.1 BGD36CF / BGD36CFG 5
2.2 GENERAL INSTRUCTIONS 5
2.3 GENERAL INFORMATION 6
2.4 RATING PLATE INFORMATION 7
3.0 VENTING 8
3.1 VENTING LENGTHS AND COMPONENTS 8
3.2 TYPICAL VENT INSTALLATIONS 9
3.3 SPECIAL VENT INSTALLATIONS 11
3.3.1 PERISCOPE TERMINATION 11
3.3.2 CORNER TERMINATION 11
3.4 VENT TERMINAL CLEARANCES 12
3.5 VENT APPLICATION FLOW CHART 13
3.6 DEFINITIONS 13
3.7 ELBOW VENT LENGTH VALUES 14
3.8 TOP EXIT HORIZONTAL TERMINATION 14
3.9 REAR EXIT HORIZONTAL TERMINATION 16
3.10 TOP OR REAR EXIT VERTICAL TERMINATION 18
4.0 PRE-INSTALLATION PREPARATION 21
4.1 DOOR OPERATION 21
4.2 REAR EXIT 21
4.3 TOP VENT 21
5.0 INSTALLATION 22
5.1 WALL AND CEILING PROTECTION 22
5.2 HORIZONTAL INSTALLATION 23
5.3 VERTICAL INSTALLATION 23
5.4 USING FLEXIBLE VENT COMPONENTS 24
5.4.1 HORIZONTAL AIR TERMINAL INSTALLATION 24
5.4.2 VERTICAL AIR TERMINAL INSTALLATION 25
5.4.3 APPLIANCE VENT CONNECTION 26
5.5 USING RIGID VENT COMPONENTS 26
5.5.1 HORIZONTAL AIR TERMINAL INSTALLATION 26
5.5.2 EXTENDED HORIZONTAL AND CORNER TERMINAL INSTALLATION 26
5.5.3 VERTICAL AIR TERMINAL INSTALLATION 27
5.6 VERTICAL THROUGH EXISTING CHIMNEY 28
5.7 MOBILE HOME INSTALLATION 29
5.8 GAS INSTALLATION 29
5.9 OPTIONAL WALL SWITCH EXCLUDING BGD36CFG 30
6.0 FRAMING 30
6.1 INSTALLING STAND-OFFS 31
6.2 MINIMUM FRAMING DIMENSIONS 32
6.2.1 STEEL HEADER INSTALLATION 33
6.3 MINIMUM ENCLOSURE CLEARANCES 34
6.3.1 REAR VENT ENCLOSURE 34
6.3.2 TOP VENT ENCLOSURE 35
6.3.4 FINISHED FLOOR INSTALLATION 36
6.3.5 HEARTH INSTALLATION 36
6.4 NON-COMBUSTIBLE FACING MATERIAL 37
6.5 ALCOVE FRAMING 37
6.8 REMOTE RECEIVER PLACEMENT 38
6.7 MINIMUM MANTEL CLEARANCES 38
7.0 FINISHING 39
7.1 SAFETY SCREEN & DOOR INSTALLATION / REMOVAL 39
7.2 CLEAN FACE TRIM KIT INSTALLATION 40
8.0 BGD36CF FINISHING 41
8.1 LOG PLACEMENT 41
8.2 GLOWING EMBERS 42
8.3 CHARCOAL EMBERS 42
8.4 LOGO PLACEMENT 42
8.5 OPTIONAL ROCK KIT 42
9.0 FINISHING 43
9.1 GLASS BURNER INSTALLATION 43
10.0 WIRING DIAGRAM 44
10.1 LIGHT SWITCH 44
10.2 BURNER SWITCH 45
10.3 RECEPTACLE WIRING DIAGRAM 46
11.0 OPERATION 46
11.1 LIGHT OPERATION 46
11.2 BGD36CF 47
11.3 BGD36CFG 48
12.0 ADJUSTMENTS 49
12.1 PILOT BURNER ADJUSTMENT 49
12.2 VENTURI ADJUSTMENT 49
12.2.1 BGD36CF VENTURI ADJUSTMENT 49
Loading ...
Loading ...
Loading ...