Loading ...
Loading ...
Loading ...
24 25
CLEANING THE STEAM WAND
• The steam wand should always be cleaned
after texturing milk. Wipe the steam wand
with a damp cloth.
• If any of the holes in the tip of the steam
wand become blocked, it may reduce frothing
performance.
• Go to 'Settings' > 'Steam wand cleaning' and
follow the guide on the screen.
CLEANING THE FILTER BASKETS
AND PORTAFILTER
• The filter baskets and portafilter should be
rinsed under hot water immediately after use
to remove all residual coffee oils.
• If any of the holes in the filter basket become
blocked, use the pin on the end of the
provided cleaning tool to unblock the hole(s).
• If the hole(s) remain blocked, dissolve a
cleaning tablet in hot water and soak filter
basket and portafilter in solution for approx.
20 minutes. Rinse thoroughly.
CLEANING THE SHOWER SCREEN
• The group head interior and shower screen
should be wiped with a damp cloth to remove
any ground coffee particles.
• Periodically purge the machine. Place an
empty filter basket and portfilter into the
group head. Touch the 'Brew' button and run
a short flow of water to rinse out any residual
coffee.
CLEANING THE DRIP &
STORAGE TRAY
• The drip tray should be removed, emptied
and cleaned at regular intervals, particularly
when the drip tray full indicator is showing
EMPTY ME!
• Remove the grid from the drip tray.
Lift the coffee grind separator and dispose
of any coffee grounds. The EMPTY ME!
indicator can also be removed from the drip
tray by pulling upwards to release the side
latches. Wash all parts in warm soapy water
with a soft cloth. Rinse and dry thoroughly.
• The storage tray (located behind the drip
tray) can be removed and cleaned with a soft,
damp cloth. Do not use abrasive cleansers,
pads or cloths which can scratch the surface.
NOTE
All parts should be cleaned by hand using
warm water and a gentle dish washing liquid.
Do not use abrasive cleansers, pads or cloths
which can scratch the surface. Do not clean
any of the parts or accessories in the
dishwasher.
CLEANING THE OUTER HOUSING &
CUP WARMING TRAY
The outer housing and cup warming tray can
be cleaned with a soft, damp cloth. Polish with
a soft, dry cloth. Do not use abrasive cleansers,
pads or cloths which can scratch the surface.
STORING YOUR MACHINE
Before storing, press the POWER button to
switch the machine off and remove the plug
from the power outlet. Remove unused beans
from the hopper, clean the grinder (see
page 23), empty the water tank and the drip
tray. Ensure the machine is cool, clean and dry.
Insert all accessories into the storage tray.
Store upright. Do not place anything on top.
WARNING
Do not immerse power cord, power plug or
appliance in water or any other liquid.
USING THE ALLEN KEY
Over time, the silicone seal surrounding the
shower screen will need to be replaced to
ensure optimum brewing performance.
1. Press the POWER button to switch the
machine off and unplug the cord from the
power outlet.
2. Carefully remove the water tank and drip
tray, taking particular care if they are full.
3. Using a skewer or similar, clean the center
of the screw of any residual coffee.
4. Insert the shorter end of the Allen Key
into the center of the screw. Turn counter-
clockwise to loosen the screw.
Clean center of screw
before inserting Allen Key.
5. Once loosened, carefully remove and retain
the screw and the stainless steel shower
screen. Make note of the side of the shower
screen that is downwards. This will make
re-assembly easier. Wash the shower screen
in warm soapy water, then dry thoroughly.
6. Remove the silicone seal with your fingers
or a pair of long-nose pliers. Insert the new
seal, flat side first, so the ribbed side is
facing you.
7. Re-insert the shower screen, then the screw.
With your fingers, turn the screw clockwise
for 2-3 revolutions then insert the Allen Key
to tighten until the screw is flush with the
shower screen. Do not overtighten screw.
8. Re-insert the drip tray and water tank.
Contact Breville Consumer Support or visit the
Breville webpage for replacement silicone seals
or for advice.
TRANSPORTING AND STORING
Press the POWER button to switch the
machine off and remove the plug from the
power outlet. Remove unused beans from the
hopper, clean the grinder, empty the water
tank and the drip tray. Ensure the machine is
cool, clean and dry. Insert all accessories into
the storage tray. Store upright. Do not place
anything on top.
Loading ...
Loading ...
Loading ...