Loading ...
Loading ...
Loading ...
Proper care and cleaning are
important
so
your range will give
you efficient and satisfactory service.
Follow these directions carefully in
caring for your range to assure safe
and proper maintenance.
(on
models so equipped)
Clean the area under the drip pans
often. Built-up soil, especially
grease, may catch fire. To make
cleaning easier, the plug-in surface
units are removable.
The porcelain enamel finish is
sturdy but breakable if misused.
This finish is acid-resistant.
However.
any
acid foods spilled
(such as fruit juices, tomato, or
vinegar) should not be permitted
to remain on the finish.
Your range is vented through a duct
located under the right rear surface
unit. Clean the duct often.
Note:
oil
.$()[)1(’ t?l(M/t’!.Y,
t“ejlt’ctol-
pa)l/ri~lg.v
are
o~le
pitw.
To remove:
Q
Make sure unit is cool.
● Lift up right rear surface unit.
●
Remove trim ring and drip pan.
s
Lift out oven vent duct.
To replace:
s
Place the part over the oven vent
located below the cooktop with the
opening of the duct under the round
opening in the drip pan. It is
important that the duct is in the
correct position so moisture and
vapors from the oven can be
released during oven use. NOTE:
Never cover the hole in the oven
vent duct with aluminum foil or
my
other material. This prevents
the oven vent from working
properly during any cooking cycle.
I
I
Receptacle
To clean:
●
Wipe around the edges of the
surface unit opening in the range
top. Clean the area below the unit.
Rinse
all
washed areas with a damp
cloth or sponge. Caution: Be sure
all
controls are turned OFF before
attempting to clean under the cooktop
or removing the surface units.
To remove:
●
Raise the unit coil opposite the
receptacle. Lift about one inch
above the trim ring and pull away
from the receptacle. Caution: Be
sure the coils are cool before
removing
a
Calrod@)
unit.
●
After removing the plug-in
surface unit, lift the trim ring and
drip pan (or one-piece pan/ring) to
clean under the unit.
To replace:
c
Place the drip pan (or one-piece
pan/ring) in the
surfhce
unit opening
in the range top. Line up the pan so
the unit receptacle can be seen. If
the trim ring is separate, put it in
place over the drip pan.
c
Insert the terminals of the plug-in
unit through the opening in the pan
and into the receptacle.
c
Guide the surface unit into place
so it fits evenly and fits snugly into
the trim ring.
NOTE: If trim ring and drip pan
are separate, the drip pan
must
be
under the trim ring.
29
CAUTION
●
Do not attempt to clean plug-in
surface units in
an
automatic
dishwasher.
●
Do not immerse plug-in surface
units in liquids of any kind.
●
Do not bend the plug-in surface
unit plug terminals.
● Do not attempt to clean, adjust
or in any way repair the plug-in
receptacle.
(on models so equipped)
This unit cannot be removed. It
Can
be lifted upward and locked in that
position for cleaning under the
unit.
Be certain the unit is cool
before lifting the coil.
After lifting coil unit, remove trim
ring and drip pan (or one-piece
pan/ring) to clean under unit.
To reposition tilt-lock unit:
● Replace drip pan (or one-piece
pan/ring) into recess in cooktop. If
trim ring is separate, put it in place
over drip pan.
●
Guide surface unit so it fits
evenly and snugly into place.
(on models so equipped)
To REMOVE door, open to BROIL
position, or where you feel hinge
catch slightly. Grasp door at sides:
life door up and away from hinges.
To REPLACE, grasp door at sides,
line up door with hinges and push
door firmly into place.
e
Loading ...
Loading ...
Loading ...