MINI TWIN BARREL BICYCLE FOOT PUMP, LARGE PRESSURE
GAUGE, 120PSI, PORTABLE AIR PUMP, WITH ACCESSORIES
MODEL NO: FP7
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9 Read the manual before using this product. Thoroughly understand operating procedures, safety warnings and maintenance.
9 Keep the manual in a convenient place for all users to see and use. Keep labels as per original.
WARNING! : Use on hard level surface.
9 Damage can occur from continued overuse.
9 The pump may become HOT after using for a long period of time.
9 Allow the pump to cool down suciently before storing.
9 Only inate tyres to the manufacturer’s recommended pressure. DO NOT over inate as serious injury could occur.
9 Keep the pump away from small children.
9 Children from age 8 years and above, persons with reduced physical, sensory, or mental capabilities, those with lack of experience and
knowledge can use the appliance if they have been given supervision or instruction concerning use of the appliance in a safe way to
understand the hazards involved.
9 Children shall NOT play with the appliance.
9 Clean with a damp cloth only. DO NOT use chemicals or soap.
8 DO NOT use (or modify) the tool for any other purpose than that for which it was designed.
9 The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and caution are applied when using this product. Failure to heed
these warnings may result in fatal personal injury and/or property damage.
9 Cleaning and user maintenance on the appliance shall not be made by children without supervision.
2. INTRODUCTION
Compact and lightweight design for easy transportability. Twin barrel bicycle foot pump (two Ø34mm cylinders) featuring low (4bar/60psi)
and high-pressure modes (8bar/120psi). Large pressure gauge with easy-to-read scale in both psi and bar. Long 410mm hose with tyre valve
connector with integrated Schrader and Presta connector attachments Supplied with ball spike and 2 inatables adapter which have an integral
storage on the pump. S
3. SPECIFICATION
Model No.: ...................................................................... FP7
Nett Weight: ..................................................................0.5kg
Max. Pressures: Low setting 4 bar (60psi), High setting 8 bar (120psi)
4. CONTENTS
See g.1 and g.2.
Pump Body
Ball Spike adaptor
Two inatable adaptors
Delivery Hose 410mm long (Connector Schrader and Presta compatible)
5. OPERATION
NOTE: This foot pump is suitable for inating all common bicycle tyres, air mattresses, inatables, etc. Any other use or misuse of
the product is considered improper and may lead to the risk of injuries and damage. The distributor assumes no liability for damage
resulting from improper use.
NOTE: The pump output can be changed using the lever on the base of the pump (g 2). The low setting max output is 60psi, lever
in the down position (g.2). The high setting max output is 120psi, place the lever in the up position (g.2).
Original Language Version
© Jack Sealey Limited
Refer to
instructions
FP7 Issue 1 02/04/25
Connector
Locking Lever
g.1
Wear eye
protection
5.1. Place the pump on a level and stable surface.
5.2. NOTE: The connector has both Shrader (marked S) or Presta (marked P) valves
(g.4.). Apply appropriate connector to the valve of the tyre to be inated and
then lock with locking lever (g.3).
5.3. If you are working with an adapter, insert the desired adapter into the larger
Schrader connector port and close the locking lever down (g.1). Insert the
other end of the adapter into the ination orice of the object to be inated.
5.4. Place foot on foot pedal. Pump up the object connected to the pump with
uniform strokes. Inate until desired pressure is reached. When doing
so, observe the maximum lling pressure specied by the manufacturer
that the pump hose is not kinked.
5.5. Release the locking lever (g.3) to remove the connector from valve / adaptor.
5.6. MAINTENANCE
5.7. Clean regularly with a damp cloth, DO NOT use chemicals or soap.
5.8. DO NOT submerge in water. Store in a dry, childproof area. This helps prevent the unit from damage and possible personal injuries.
5.9. When transporting the pump, always do so by holding the body.
5.10. Only use the pump for the intended use.
6. END OF LIFE
6.1. Dispose of unit in accordance with local, regional and national guidelines.
g.2
Pressure adjustment lever,
Turn down max output 60psi
Turn up max output 120psi
Adaptor
Housing
g.3
FP7 Issue 1 02/04/25
Original Language Version
© Jack Sealey Limited
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 sales@sealey.co.uk www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Unlocked
Position
Locked
Position
g.4
