Loading ...
Loading ...
Loading ...
To assemble and ao}ust your tractor you will need:
(2) 7/16" Wrenches
(I) 3/4" Wrench
•(1) 9/16" Wrench
(I) !/2" Wrench
(1) 3/4" Socket
Ratchet wrench
Tire Pressure Gauge
Screwdriver
Utility Knife
NOTE: RIGHT HAND (R.H.) AND LEFT HAND (L.H.)
ARE DETERMINED FROM OPERATOR'S POSITION
WHILE SEATED ON THE TRACTOR.
WEAR EYE AND FACE SHIELD.
_[ WASH HANDS OR CLOTHING IMME-
D_ATELY iF ACCIDENTALLY iN CON-
TACT W_TH BATTERY ACID°
DO NOT SMOKE, FUMES FROM
CHARGED BATTERY ACID ARE E×-
PLOSIVE°
NOTE: THIS TRACTOR IS EQUIPPED WITH AN OP-
ERATOR PRESENCE SENSING SW_TCH. ANY AT-
TEMPT BY THE OPERATOR TO LEAVE THE SEAT
WITH THE ENGINE RUNNING AND ATTACHMENT
CLUTCH ENGAGED WILL SHUT OFF THE ENGINE.
t. Prepare Battery
READ INSTRUCTIONS INCLUDED WITH THE BATTERY
VENT CAPS FOUND iN BAG OF PARTS. ALWAYS WEAR
GLOVES, CLOTHING AND GOGGLES TO PROTECT
YOUR HANDS, SKIN AND EYES.
a. Fili and charge battery (before installing). NOTE:
SEE DETklLED iNSTRUCTiONS PACKAGED
WiTH B_,N-E RY VENT CAPS IN BAG OF PARTS.
NOTE: OVERCHARGING WILL SHORTEN BATTERY
LIFE.
b. Fitl battery with battery acid to bottoms of tubes in
cells (.Fig 1). DO NOT OVERFILL. OVERFILLING
WILL RESULT tN DAMAGE TO TRACTOR.
c. Check le vet of battery acid after 30 minutes. Add
additiona/batteryacidifnecessary. NOTE: PRESS
VENT CAPS iNTO BATTERY UNTIL FASTENED
SECURELY.
CUT AWAY VIEW
I ...........................
SEAT PAN
ASSEMBLY
--- ENT CAP
BATTERY
IBE
BATTERY
CELL
FIGURE I
SEAT
NOTE: OBSERVE SAFETY PRECAUTIONS, LISTED
IN BOX ABOVE, REQUIRED FOR BATTERY CHARG-
INGr
d.
e.
Charge battery at a rate of six amperes for one
hour.
Neutralize excess batterer acid (from tilting battery)
for disposal by adding _t to 9 fitres (2 gallons) of
water in a 23 litre (5 gallon) plastic container. Stir
with a wooden or plastic paddle while adding
baking soda unti! the addition of mere soda causes
no more foaming.
2. Install Seat
Seat position should be adjusted forward or backward so
that the operator can comfortably reach Clutch!Brake Pedal
and safely operate the tractor (Fig. 2).
a.
b.
Remove cardboard from seat pan.
Place seat on seat pan. Screw adjustment knob
and ffat washer into seat (F_g. 3). Screw shoulder
bolt into seat (Fig. 3). Adjustment knob, shoulder
bolt and washers found in bag of parts (shown full
size on page 6)_
ADJUSTMENT FLAT FENDER
KNOB WASHER SHIFT
FIGURE 2
_ TIGHTENED SECURELY TO PREVENT
MOVEmeNTSEA',"
c. Tighten shoulder bolt using a 1/2" wrench. NOTE:
THE SHOULDER BOLT WILL BE LOOSE tN THE
SEAT PAN SLOT.
d. Tighten adjustment knob finger tight.
e. Place seat in operating position. Sit on the seat and
press clutchforake pedal all the way down. ff operat-
ing position is not comfortable, adjust seat.
f. To adjust: raise seat. Loosen adjustment knob.
Slide seat to desired position. Tighten adjustment
knob securely.
Loading ...
Loading ...
Loading ...