Loading ...
Loading ...
Loading ...
5554
TO CANCEL THE DELAY TIMER FUNCTION
1. Open the door of the dishwasher.
2. Press and hold Delay Timer key for 3 seconds.
3. At the end of 3 seconds, delaying process will be canceled.
• If the program is changed, the delay timer is canceled.
• Delay Timer function can not be set after the program starts.
STARTING THE PROGRAM
• First, open the door of the dishwasher. In order to start the dishwasher after
selecting the program and auxiliary functions, press the Start/Pause + On/
Off key. Once the program starts, the estimated time remained to the end of the
program will appear on the display.
• The dishwasher performs water softening depending on the hardness level of the
supply water. Remaining time displayed towards the end in some programs can
be different from the time indicated at the beginning due to this process. The total
time can also change while the program is running depending on the ambient
temperature where the dishwasher is installed, temperature of the supply water
and amount of the dishes.
• Pay attention not to open the door of the dishwasher when it is running. Stop the
dishwasher by pressing Start/Pause key as soon as the door of the dishwasher is
opened. In other situation, the dishwasher will stop automatically after 4 seconds
when the door of the dishwasher is opened and any key is not pressed. To start a
program, Start/Pause key is pressed and close the door of the dishwasher within
4 seconds.
• If the door is opened while the dishwasher is running, the dishwasher will switch
to the standby mode. Press Start/Pause key and close the dishwasher door
within 4 seconds, then the program will resume.
CANCELING THE PROGRAM
1. Press program Selection + Cancel key for 3 seconds to cancel the program.
2. After 3 seconds, “1” will appear on the display. For a couple of minutes the
dishwasher will fulfill the necessary operations required to cancel the program.
• There might be residues of detergent or rinse aid left in the dishwasher and/or on
the pieces being washed depending on what step the canceled program was in.
OPERATION
SALT INDICATOR
Please check the salt indicator on the control panel to see whether there is adequate
amount of softening salt in the dishwasher or not. Refill the salt reservoir with salt
whenever salt warning indicator appears on the control panel of the dishwasher.
RINSE AID INDICATOR
Please check the rinse aid indicator on the control panel to see whether there is
adequate amount of rinse aid in the dishwasher or not. Refill the rinse aid reservoir
with rinse aid whenever rinse aid warning indicator appears on the control panel of
the dishwasher.
END OF PROGRAM
“00” will be displayed when the washing program is over.
1. Open the door of the dishwasher.
2. Press Start/Pause + On/Off key to turn off the dishwasher.
• Leave the dishes in the dishwasher for about 15 minutes to cool down after they
are washed. The dishes will dry in a shorter time if the door is left ajar during this
period. This process will increase the drying effectiveness of the dishwasher.
WATER CUT - OFF WARNING
If main water is cut or water inlet tap is turned off, the dishwasher can not take water
in and “FF” will flash continuously on the display. As long as the problem continues,
the washing program is stopped and water inlet is checked regularly by the user. If
the water inlet is provided, the dishwasher gets ready to start a new program.
OVERFLOWING WARNING
If the dishwasher intakes too much water or there is leakage at any of the
components, then the dishwasher will detect this and “F1” will flash on the display. As
long as the overflowing continues, safety algorithm will be active and try to discharge
the water. If overflowing stops and safety is assured, “F1” will disappear. If “F1” does
not disappear, there is a permanent fault. In this case, the authorized service should
be contacted.
OPERATION
Starting the Program
End of Program
Loading ...
Loading ...
Loading ...