Loading ...
Loading ...
Loading ...
2726
Test Strip ( For Models With Water Softener )
Run water
through the
tap (1min.)
Keep the
strip in the
water (1sec)
Shake the
strip.
Wait
(1min.)
Set the hardness level of
your machine.
1
2
3
4
5
6
WARNING:
TEST STRIP
The washing effectiveness of your dishwasher depends on the softness of the tap
water. For this reason, the dishwasher is equipped with a system that reduces the
hardness in the main water supply. The washing effectiveness will increase when the
system is correctly set. To find out the water hardness level of water in your area,
contact your local Water Board or determine water hardness level by using the test
strip. Follow the steps in the image when using the test strip:
WARNING: If the water is well water or has a hardness level above 9° F,
we recommend that you use filter and refinement devices.
Adjust the water hardness setting of the dishwasher according to the level specified
on the test strip.
NOTE: Hardness level is adjusted to level 1 as a factory setting.
NOTE: If only combination products are used, the softener level can be changed.
Keep water
through the tap
(1 min)
Keep the strip
in the water
(1 sec)
Shake the strip Wait
(1 min)
Set the hardness
level of the
dishwasher
Test Strip ( For Models With Water Softener )
Run water
through the
tap (1min.)
Keep the
strip in the
water (1sec)
Shake the
strip.
Wait
(1min.)
Set the hardness level of
your machine.
1
WARNING:
Test Strip ( For Models With Water Softener )
Run water
through the
tap (1min.)
Keep the
strip in the
water (1sec)
Shake the
strip.
Wait
(1min.)
Set the hardness level of
your machine.
WARNING:
Test Strip ( For Models With Water Softener )
Run water
through the
tap (1min.)
Keep the
strip in the
water (1sec)
Shake the
strip.
Wait
(1min.)
Set the hardness level of
your machine.
1
WARNING:
Test Strip ( For Models With Water Softener )
Run water
through the
tap (1min.)
Keep the
strip in the
water (1sec)
Shake the
strip.
Wait
(1min.)
Set the hardness level of
your machine.
1
WARNING:
Test Strip ( For Models With Water Softener )
Run water
through the
tap (1min.)
Keep the
strip in the
water (1sec)
Shake the
strip.
Wait
(1min.)
Set the hardness level of
your machine.
WARNING:
1 minute
1 second
1 minute
1
2
3
4
5
6
Level Temperature (F) Indicator
1 0-9° F L1 is shown on the display.
2 10-20° F L2 is shown on the display.
3 21-30° F L3 is shown on the display.
4 31-40° F L4 is shown on the display.
5 41-55° F L5 is shown on the display.
6 56-90° F L6 is shown on the display.
OPERATION
SALT INDICATOR
Please check the salt indicator on the control panel to see whether there is adequate
amount of softening salt in the dishwasher or not. Refill the salt reservoir with salt
whenever salt warning indicator appears on the control panel of the dishwasher. In
order to add salt to the dishwasher,
1. Open the door of the dishwasher,
2. Press and hold “Start/Pause + On/Off” key for 3 seconds,
3. The dishwasher gives an audible warning when it is ON,
4. Then, press and hold “Program Selection + Cancel” key until “SL” is represented
on the display, display, the dishwasher will display the last setting,
5. The amount of Salt is adjusted by pressing “Program Selection + Cancel” key,
6. After the adjustment, turn off (by pressing Start/Pause + On/Off key) the
dishwasher to save the selected salt amount.
SALT REFILL INDICATOR
WARNING: If the salt indicator light comes on during a program, wait until
the end of the program to fill the salt reservoir with dishwasher salt.
After the salt reservoir has been filled, the refill indicator may still be lit up if the salt
concentration has not yet reached the correct level. It will go out when the correct
concentration is reached.
NOTE: The salt refill indicator will be turned off if the dishwasher has been
programmed for a water hardness below 9° F.
OPERATIONOPERATION
Setting the Water Softener
Salt Indicator
WARNING
WARNING
Loading ...
Loading ...
Loading ...