Loading ...
Loading ...
Loading ...
MAINTENANCE
33
ENGLISH
EasyClean® INSTRUCTION GUIDE
1. Remove oven racks and accessories from the oven.
2. Scrape off and remove any burnt-on debris with a
plastic scraper.
Suggested plastic scrapers:
•
Hard plastic spatula
•
Plastic pan scraper
•
Plastic paint scraper
•
Old credit card
3. Fill a spray bottle (10 oz or 300 ml) with water and
use the spray bottle to thoroughly spray the inside
surfaces of the oven.
4. Use at least
1
/
5
(2 oz or 60 ml) of the water in the
bottle to completely saturate the soil on both the
walls and in the corners of the oven.
5. Spray or pour the remaining water (8 oz or 240 ml)
onto the bottom center of the oven cavity. The
indentation on the oven bottom should be fully
covered to submerge all soils. Add water if necessary.
If cleaning multiple ovens, use an entire bottle of
water to clean each oven. Do not spray water directly
on the door. Doing so will result in water dripping to
the floor.
NOTE
6. Close the oven door.
Press the button to select the upper or lower
Easyclean®.
Press START.
•
Some surfaces may be hot after the EasyClean® cycle.
Wear rubber gloves while cleaning to prevent burns.
•
During the EasyClean® cycle, the oven bottom becomes
hot enough to cause burns. Wait until the cycle is over
before wiping the inside surface of the oven.
Failure to do so may result in burns.
•
Avoid leaning or resting on the oven door glass
while cleaning the oven cavity.
CAUTION
7. A tone will sound at the end of the 10-minute cycle.
Press UPPER or LOWER CLEAR/OFF to clear the
display and end the tone.
8. After the cleaning cycle and during hand-cleaning,
enough water should remain on the oven bottom
to completely submerge all soils. Add water if
necessary. Place a towel on the floor in front of the
oven to capture any water that may spill out during
hand-cleaning. If you are cleaning the upper oven on
a double oven, it is also best to cover the holes in the
top of the lower oven door with a towel to capture
any water that may drip into the door during hand-
cleaning.
9. Clean the oven cavity immediately after the
EasyClean® cycle by scrubbing with a wet, non-
scratch scouring sponge or pad. (The scouring side
will not scratch the finish.) Some water may spill into
the bottom vents while cleaning,
but it will be captured in a pan
under the oven cavity and will not
hurt the burner.
DO NOT use any steel scouring pads, abrasive pads
or cleaners as these materials can permanently
damage the oven surface.
NOTE
10. Once the oven cavity is cleaned, wipe any excess
water with a clean dry towel. Replace racks and any
other accessories.
11. If some light soils remain, repeat the above steps,
making sure to thoroughly soak the soiled areas.
If stubborn soils remain after multiple EasyClean®
cycles, run the Self Clean cycle. Be sure that the oven
cavity is empty of oven racks and other accessories,
and that the oven cavity surface is dry before
running the Self Clean cycle. Consult the Self Clean
section of your owner’s manual for further details.
•
If you forget to saturate the inside of the oven
with water before starting EasyClean®, press
UPPER or LOWER CLEAR/OFF. Wait for the oven to
cool to room temperature and then spray or pour
water into the oven and start another EasyClean®
cycle.
•
The cavity gasket may be wet when the
EasyClean® cycle finishes. This is normal. Do not
clean the gasket.
•
If mineral deposits remain on the oven bottom
after cleaning, use a cloth or sponge soaked in
vinegar to remove them.
NOTE
Loading ...
Loading ...
Loading ...