Loading ...
Loading ...
Loading ...
10
tween the surfaces of the appliance and the side and rear
walls and at least 15 cm above the coee maker.
• Water penetrating the coee maker could cause damage.
Do not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes. Do not install the appliance in a room where the
temperature could drop below freezing point.
• Arrange the cord in such a way that it cannot be damaged
by sharp edges or contact with hot surfaces (e.g. electric
hot plates).
5.3 Connecting the appliance
Important!
Check that the mains power supply voltage corresponds to that
indicated on the rating plate on the bottom of the appliance.
Connect the appliance to a correctly installed and eciently
earthed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualied
electrician.
5.4 Setting up the appliance
Please note!
• Coee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of cof-
fee in the mill. The machine is, however, guaranteed to be
new.
• You should customise water hardness as soon as possible
following the instructions in section “18. Setting water
hardness”.
1. Plug the power cord (C8) connector into the socket (A20) at
the back of the appliance and connect the appliance to the
mains electricity supply (g. 1). Make sure the main switch
(A21) at the back of the appliance is pressed (g. 2);
2. “SELECT LANGUAGE”: press the ag corresponding to the
required language;
then follow the instructions which appear on the appliance
display:
3. “FILL TANK WITH FRESH WATER”: remove the water tank
(A16) (g. 3), open the lid (A15) (g. 4), ll to the MAX line
with fresh water (g. 5), close the lid and put the tank back
in the appliance (g. 6);
4. “INSERT WATER SPOUT”: Check that the hot water/steam
spout (C6) is inserted on the connection nozzle (A9) (g. 7)
and place a container holding a minimum of 100 ml under-
neath (g. 8);
5. “WATER CIRCUIT EMPTY PRESS OK TO START FILLING PRO-
CESS” appears on the display;
6. Press “
OK” to conrm. The appliance delivers water
from the spout (g. 8) then goes o automatically.
The coee machine is now ready for normal use.
Please note!
• When setting up the appliance, you need to make 4-5 cups
of coee or 4-5 cappuccinos before the appliance starts to
give satisfactory results.
• When making the rst 5-6 cappuccinos, it is normal to hear
the noise of boiling water. After this, the noise becomes
less.
• To improve the performance of your appliance, we recom-
mend installing a water softener lter (C4) as described
in section “19. Water softener lter”. If your model is not
provided with a lter, you can request one from De’Longhi
Customer Services.
6. TURNING THE APPLIANCE ON
Please note!
Before turning the appliance on, make sure the main switch
(A21) is pressed (g. 2).
Each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted. The appli-
ance is ready for use only after completion of this cycle.
Danger of burns!
During rinsing, a little hot water comes out of the coee spouts
(A8) and is collected in the drip tray (A14) underneath. Avoid
contact with splashes of water.
• To turn the appliance on, press the
button (A7-g.
9). The message “HEATING UP UNDERWAY PLEASE WAIT”
appears on the display.
When heating is complete, the message changes to “RINSING
UNDERWAY, HOT WATER FROM SPOUTS”. As well as heating the
boiler, this also heats the internal circuits by circulating hot
water.
The appliance is at temperature when the main screen (home-
page) appears.
7. TURNING THE APPLIANCE OFF
Whenever the coee machine is turned o after being used to
make coee, it performs an automatic rinse cycle.
Danger of burns!
During rinsing, a little hot water ows from the coee spouts
(A8). Avoid contact with splashes of water.
• To turn the appliance o, press the button (A7) (g.
9).
Loading ...
Loading ...
Loading ...