OWNER’S MANUAL AND SAFETY INSTRUCTIONS
5T HYDRAULIC CAR RAMP
ITEM # 50525
SAVE THIS MANUAL. KEEP THIS MANUAL FOR SAFETY WARNINGS, PRECAUTIONS, ASSEMBLY,
OPERATION, INSPECTION, MAINTENANCE AND CLEANING PROCEDURES. WRITE THE PRODUCT’S
SERIAL NUMBER ON THE BACK OF THE MANUAL, OR THE MONTH AND YEAR OF PURCHASE IF
PRODUCT HAS NO SERIAL NUMBER
FOR QUESTIONS, PLEASE CALL CUSTOMER SERVICE: 909.628.4900
SAFETY WARNINGS
Read all safety warnings and instructions. Failure to follow the warnings and
instructions may result in injury and/or property damage. Save all warnings and
instructions for future reference.
The warning and safety instructions in this manual are not meant to cover all possible conditions and
situations that may occur. Common sense, caution and care must be exercised when operating or
cleaning tools and equipment. Always contact your dealer, distributor, service agent or manufacturer
about problems or conditions you do not understand before operating the product.
SAVE THESE WARNINGS.
1
• For safety, this product is limited to use for vehicles of less than 2 tons.
• Drive the vehicle to the level road parking place the ramp in from of the front wheel and the central position of
the front wheels.
• Only experinced drivers and operators should use the adjustable car lift.
• Please make sure that the wheels are running in the middle of the ramp.
• After the vehicle is parked to the ramp, please remember to pull the handbrake, to avoid the harm caused by
the shaking of the vehicle.
• You can place the retaining device at the rear wheels to prevent the vehicle backward.
• Do not use when the product is found to have damage, bending and other factors that aect the safety.
• CHECK FOR DAMAGED PARTS. Check for alignment of moving parts, breakage of parts or any condition
that may aect its operation. Do not use lift if any component is broken or damaged.
• This product is suitable for the use of vehicles close to the angle greater than 17 degrees.
• No more than 4400lbs maximum load weight at a time.
• Be sure to safely stop the vehicle and xed hydraulic drive on ramp.
• Visually inspect the site where the lift is to be installed and check for cracked or defective concrete.
Do not attempt to use this lift if you have never been trained on basic automotive lift procedures.
Never attempt to lift components without proper lifting tools such as forklift or cranes. Stay clear of
any moving parts that can fall and cause injury. These instructions must be followed to insure proper
installation and operation of your lift. Failure to comply with these instructions can result in serious
bodily harm and void product warranty. Manufacturer will assume no liability for loss or damage of any
kind, expressed or implied resulting from improper installation or use of this product.
SAFETY WARNINGS PARTS AND MAINTENANCE
SAVE THESE WARNINGS.
1
2
1. Regularly check whether the Hydraulic drive-on ramp deformation and cracks.
2. Clean pollution of any kind on the Hydraulic drive-on ramp after each use such as Oil
stains, etc.
3. Regularly check whether all the screws are loose and reinforce the screws.
MAINTENANCE
DISCLAIMER
3
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED
TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR
REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT
PARTS THERETO.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
MADE IN CHINA
