Loading ...
Loading ...
Loading ...
INSTALLATION STEP 11
InstalltheDoorContro/
iNTRODUCTiON
NOTE: OlderCraftsman accessories and third party products are
not compatible.
Your garage door opener is compatible with up to 2 AssureLinkTM
door controls.
Install the door control within sight of the door at a minimum
height of 5 feet (1.5 m) where small children cannot reach,and
away from the moving parts of the door.
NOTE:For gang box installations it is not necessaryto drill holes
or install the drywall anchors. Usethe existing holes in the gang
box.
WiRETHE DOORCONTROL(FIGURE1)
1. Strip 7/16 inch (11 mm) of insulation from one end of the wire
and separate the wires.
2. Connect one wire to each of the two screws on the back of the
door control. The wires can be connected to either screw.
Pre-wired installations:Choose any two wires to connect, but
make note of which wires are used so that the correct wires are
connected to the garage door opener in a later step.
MOUNTTHEDOORCONTROL(FIGURE2)
1. Mark the location of the bottom mounting hole and drill a
5/32 inch (4 mm) hole.
2. install the bottom screw, allowing 1/8 inch (3 mm) to protrude
from the wail.
3. Position the bottom hole of the door control over the screw and
slide down into place.
4. Lift the push bar and mark the top hole.
5. Removethe door control from the wall and drill a 5/32 inch
(4 mm) hole for the top screw.
6. Position the bottom hole of the door control over the screw and
slide down intoplace. Attach the top screw.
WiRE THE DOORCONTROLTOTHE GARAGEDOOROPENER
(FIGURE3)
Pre-wired installations: When wiring the door control to the
garagedoor opener makesure you use the same wires that are
connected to the door control.
1. Run the white and red/white wire from the door control to the
garagedoor opener. Attach the wire to the wall and ceiling with
the staples (not applicable for gang box or pre-wired
installations). Do not piercethe wire with the staple as this may
cause a short or an open circuit.
2. Strip 7/16 inch (11 mm) of insulation from the other end of the
wire nearthe garage door opener.
3. Connect the wire to the red and white terminals on the garage
door opener.
To prevent possible SERIOUSINJURYor DEATHfrom
electrocution:
* Be sure power is NOT connected BEFOREinstalling door
control.
* Connect ONLYto 12 VOLT low voltage wires.
To prevent possible SERIOUSINJURYor DEATHfrom a
closing garage door:
* install door control within sight of garage door, out of reach
of children at a minimum height of 5 feet (1.5 m), and away
from ALL moving parts of door.
* NEVERpermit children to operate or play with door control
push buttons or remote control transmitters.
* Activate door ONLYwhen it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
* ALWAYSkeep garage door in sight until completely closed.
NEVERpermit anyone to cross path of closing garage door.
HARDWARESHOWN ACTUAL SiZE
(std installation)
(Pre-wired)
Insulated Staples
(Not shown)
Drywall Anchors
Figure1
PRE-WIRED INSTALLATIONS: Top Mounting Hole
Choose any two wires to \
connect, but make note of
which wires are used.
Strip wire 7/16"
(11 mm)
Figure2
Bell Wire
Bottom Mounting Hole
6ABxl-1/4" Screw m
6ABx1-1/4"
Figure3
Door Control
Connections
Stripwire
7/16"(11 mm)
To insert or release wire, push
in tab with screwdriver tip
22
Loading ...
Loading ...
Loading ...