Waldorf GP8910GEC 800 Series 900mm Gas Griddle Electric Convection Oven Range

Installation Operation Manual - Page 16

For GP8910GEC.

PDF File Manual, 16 pages, Read Online | Download pdf file

GP8910GEC photo
Loading ...
Loading ...
Loading ...
14
These griddles are fitted with a pilot as a standard option and Flame Failure Protection, which is
incorporated by way of a thermo-electric system for each main burner. Flame Failure Protection will shut
off gas supply to burner in event that pilot for that burner goes out, so that un-burnt gas is not expelled.
This is an important safety feature which is slowly becoming law throughout the world
.
1. Depress gas control knob and rotate anti-clockwise to PILOTposition.
2. With gas control knob held in depressed position, to ignite pilot burner, press piezo ignition button
located on griddle control panel to the right of gas control knob. (Each press of piezo igniter button
will generate a single spark).
3. Hold INgas control knob for approximately 10-15 seconds, then release. Pilot burner should
remain alight. (If not, repeat Steps 1 to 3 above).
4. Pilot ignition can be viewed through opening in piezo igniter plastic surround.
5. To light remaining pilots, repeat Steps 1 to 4 above.
NOTE: If pilot burner goes out during normal operation wait 5 minutes before attempting to
re-light pilot burner.
1. Ensure pilot burner is alight by checking through opening in plastic surround fitted to piezo igniter
button on front control panel.
2. Rotate gas control knob anti-clockwise to desired temperature marked on knob.
3. Main burner will ignite automatically off pilot burner.
This griddle is fitted with an overtemp device which isolates gas supply to burners should gas control
system or thermostat malfunction, thus preventing overheating of griddle. If pilot fails to ignite after
several attempts, ensure that overtemp is checked to ensure that it has not tripped.
1. To reset overtemp, remove gas control
knobs from front of griddle. These are
a push fit onto spindle of gas valves.
2. Slacken 2 screws securing front control
panel to front of griddle and carefully
remove control panel, ensuring that
leads to piezo igniter are disconnected
from rear of piezo buttons.
3. Using a small screwdriver, depress
centre of overtemp reset button.
4. Re-connect piezo igniter leads to rear
of piezo igniter buttons.
5. Refit front control panel onto griddle and
secure in position with 2 securing
screws.
6. Refit gas control knobs to gas spindles.
7. Attempt to re-light pilot burners as shown above. Should pilot burners still not ignite, call a qualified
service person to investigate problem.
Overtemp fitted to
Gas Control Valve.
Overtemp
Reset Button
Fig 6
SURFACE TEMPERATURE OF THE GRIDDLE PLATE CAN REACH OVER 235°C WHEN THE APPLIANCE IS
OPERATED AT FULL SETTING.
15
1. Turn gas control knob clockwise to pilot position. Main burner will extinguish and pilot burner will
remain alight.
2. To turn 'OFF' appliance completely, turn gas control knob fully clockwise to 'O' position, pilot burner
will extinguish.
Oven is fitted with top and bottom elements. Thermostat maintains overall oven temperature. Top
element is further controlled by oven top heat control. Convection Ovens (GP8910GEC /
GP8121GEC) are fitted with a circulation fan.
NOTE: Thermostat on oven provides overall control of temperature within oven by controlling both
elements, where as Oven Top Heat Control provides a means of balancing distribution of
heat between top and bottom of oven.
Place oven racks in desired position.
Preheat:
Preheat oven by selecting desired temperature, and turning oven top heat control (Refer to Fig 5 on
page 12) to a maximum of 2. When desired temperature is reached, amber neon will go out.
Cooking:
When desired temperature has been reached, load oven with product and set oven top heat control
to desired setting.
NOTE: When oven top heat control is set to a high setting, proportionally more heat is
produced at top of oven. (This can be used for browning, etc, during cooking operation).
With oven top heat control set on a low setting, less heat is produced from top oven
elements. (This mode is used for general baking purposes to prevent cakes, etc, from
getting too brown and crisp on top, but allows the cake to cook through).
To obtain more top heat during cooking, turn oven top heat control to a higher position. (The higher
the setting, the more top heat).
Turning OFFOven:
a. Turn oven top heat control to Ooff position. Top heating will be turned OFFand upper heating
indicator lamp (Amber) will extinguish.
b. Turn thermostat control knob to Ooff position and lower heating indicator lamp (Amber) will
extinguish. Oven is now turned OFF’.
DO NOT USE aluminium foil or trays directly on cast iron sole plate(s).
NEVER block or cover openings on each side of sole plate(s).
! IMPORTANT
! IMPORTANT
DO NOT USE aluminium foil or trays directly on cast iron sole plate(s).
NEVER block or cover openings on each side of sole plate(s).
Should any abnormal operation like;
- ignition problems,
- abnormal burner flame,
- burner control problems,
- partial or full loss of burner flame in normal operation, be noticed, the appliance requires
IMMEDIATE service by a qualified service person and should not be used until such service is
carried out.
IMPORTANT