Loading ...
Loading ...
Loading ...
18
Stainless Steel Surfaces
a. Clean the exterior surfaces of the range with hot water, a mild detergent solution and a soft
scrubbing brush. Note that the gas control knobs are a push fit onto the gas control valve
spindles and can be removed to allow cleaning of the front control panel.
b. Baked on deposits or discolouration may require a good quality stainless steel cleaner or
stainless steel wool. Always apply cleaner when the appliance is cold and rub in the direction of
the grain.
c. To remove any discolouration, use an approved stainless steel cleaner or stainless steel wool.
Always rub in the direction of the grain.
d. Remove the grease tray and clean with a mild anti bacterial detergent and hot water solution
using a soft bristled brush.
e. Dry the grease tray thoroughly with a dry cloth.
f. Dry all components thoroughly with a dry cloth and polish with a soft dry cloth.
Griddle - Chrome Plate
NOTE: To maintain the finish on chrome griddle plate, ensure that all detergent and cleaning
material has been entirely removed after each cleaning process. Appliance should be
switched On briefly to ensure griddle plate becomes dry.
a. Remove and clean grease collection drawer frequently to prevent over spills.
b. Clean griddle surface thoroughly with supplied scraper tool.
c. Allow plate to cool, then clean plate with a scrubbing brush, a mild non-abrasive detergent and
water.
d. Occasionally bleach the plate with vinegar when cold.
e. Dry griddle thoroughly with a dry cloth and polish with a soft dry cloth.
f. Griddle should be switched On briefly to ensure that griddle plate becomes dry.
Griddle Cooking Area
a. Clean griddle cooking area with a soft cloth and a mild detergent and hot water solution.
b. Baked on deposits or discolouration may require a good quality stainless steel cleaner or stainless
steel wool. Always apply cleaner when appliance is cold and rub in direction of grain.
c. Remove grease drawer and clean with a mild anti bacterial detergent and hot water solution
using a soft bristled brush. Dry grease drawer thoroughly with a dry cloth.
Stainless Steel Surfaces
a. Clean exterior surfaces of griddle with hot water, a mild detergent solution and a soft scrubbing
brush. Note, gas control knobs are a push fit onto gas control valve spindles and can be
removed to clean front of control panel.
b. Baked on deposits or discolouration may require a good quality stainless steel cleaner or stainless
steel wool. Always apply cleaner when appliance is cold and rub in direction of grain.
c. To remove any discolouration, use an approved stainless steel cleaner or stainless steel wool.
Always rub in direction of grain.
d. Remove grease tray and clean with a mild anti bacterial detergent and hot water solution using a
soft bristled brush.
e. Dry grease tray thoroughly with a dry cloth.
f. Dry all components thoroughly with a dry cloth and polish with a soft dry cloth.
NOTE: All maintenance operations should only be carried out by a qualified service person.
To achieve the best results cleaning must be regular and thorough and all controls and mechanical parts
should be checked and adjusted periodically by a qualified service person. If any small faults occur, have
them attended to promptly. Don't wait until they cause a complete breakdown. It is recommended that
the appliance is serviced every 6 months.
11
NOTE: ALL ELECTRICAL CONNECTIONS MUST ONLY BE CARRIED OUT BY A QUALIFIED
PERSON.
Each appliance should be connected to an adequately protected power supply and isolation switch
mounted adjacent to, but not behind appliance. This switch must be clearly marked and readily accessible
in case of fire.
1. Check electricity supply is correct as shown on
Rating Plate attached to lower front hand side of
front sill panel.
2. Supply terminal connections are located at rear of
appliance. Refer to ‘Electrical Connections’ in
‘Dimensions’ section of manual.
3. Open oven door and remove oven control panel to
allow connection access for electrical supply.
4. Connect mains supply to L1, L2 and L3 connection
terminals. Refer to 'Electrical Supply Requirements'
section for connection details.
NOTE: This appliance can be converted from 3 Phase
to Single Phase supply by connecting single
phase input to L1 and adding a bridge wire
between L1, L2 and L3 connections, (refer to
Fig 3 opposite and information shown in
'Electrical Supply Requirements Table' in
'Specifications' Section).
5. Connect neutral and earth conductors to neutral stud
and earth stud respectively.
6. For all connections ensure that conductors are
secure and appropriately terminated.
7. Tighten cable gland to secure against tension on
cable.
8. Check that the polarity of each connection is correct
to the mains connection terminals markings on the
appliance.
NOTE:
This appliance must be earthed.
Fixed wiring installations must incorporate an all-pole disconnection switch.
9. Correctly locate appliance into its final operating position and using a spirit level, adjust legs so that
appliance is level and at correct height.
10. Connect power supply to appliance.
11. Check electrical supply is within input rating specification, refer to ‘Specifications’ section).
Add bridging
wires between
L1, L2 and L3.
Neutral sup-
ply connection
Phase supply
connection to L1
P
N
Fig 4
THIS APPLIANCE MUST BE EARTHED. IF SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY A SUITABLY
QUALIFIED PERSON IN ORDER TO AVOID A HAZARD.
Loading ...
Loading ...
Loading ...