Loading ...
_ ,. i
i ..............
FULL ONE YEAR WARRANTY ON CRAFTSMAN TAB LE SAW
If within one year from the date of purchase, this Craftsman Table Saw fails due to a defect in
material or workmanship, Sears will repair it, flee of charge.
WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS
SERVICE CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES.
This warranty applies only while this product is in use in the United States.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.
SEARS, ROEBUCK AND CO.. Dept. 698/731A, Sears Tower, Chicago, IL 60684
GENERAL SAFETY iNSTRUCTIONS FOR POWER TOOLS
1. KNOW YOUR POWER TOOL
Read and understand the owner's manual and
iabels affixed to the tool Learn its application
end imitations as well as the specific potential
hazards peculiar to this tool.
2. GROUND ALL TOOLS
This tool is equipped with an approved 3-
conductor cord and a 3-prong grounding type
plug to fit the proper g rounding type receptacle.
The green conductor in the cord is the
grounding wire. Never con nect the green wi re to
a live terminal.
3, KEEP GUARDS IN PLACE
in working order, and in proper adjustment and
alignment.
4. REMOVE ADJUSTmNG KEYS
AND WRENCHES
Form habit of checking to see that keys and
adjusting wrenches are removed from too_
before turning it on.
5. KEEP WORK AREA CLEAN
Cluttered areas and benches invite accidents,
Floor must not be slippery due to wax or
sawdust.
6. AVOID DANGEROUS ENVIRONMENT
Z87.1) at all times. Everyday eyeglasses only
have impact resistant lenses, they are NOT
safety glasses. Also, use face or dust mask if
cutting operation is dusty, and ear protectors
(plugs or muffs) during extended periods of
operation.
13. SECt.iRE WORK
Use clamps or a vise to hold work when
practical. It's safer than using your hand, frees
both hands to operate tool.
14. DON'T OVERREACH
Keep proper footing and balance at all times.
15. MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating
and changing accessories.
16. DISCONNECT TOOLS
before servicing; when changing accessories
such as blades, bits, cutters, etc.
17. AVOID ACCIDENTAL STARTING
Make sure switch is in "OFF" position before
plugging in
18. USE RECOMMENDED ACCESSORIES
Consult the owner's manual for recommended
Don't use power tools in damp or wet locations accessories. Follow the instructions that
or expose them to rain. Keep work area well accompany the accessories. The use of
lighted. Provide adequate surrounding work improper accessories may cause hazards.
space. 19. NEVER STAND ON TOOL
7. KEEP CHILDREN AWAY Serious injury could occur if the tool is tipped or
All visitors should be kept a safe distance from
work area,
8. MAKE WORKSHOP CHILD-PROOF
-- with padlocks, master switches, or by
removing Starter keys.
S, DON'T FORCE TOOL
Iwt will do the job better and safer at the rate for
hich it was designed, and
all
if the cutting tool is accidentally contacted.
Do not store materials above or near the tool
such that it is necessary to stand on the tool to
reach them.
guard
11. WEAR PROPER PPAREL
Do not wear Ioo clothing; gioves, neckties or
jewelry (rings, _ St watches)to get caught in
nnovihg part N0nslip footwear is
recommended. Wear protective hair covering to
contain long hair. Roll long sleeves above the
elbow.
12. USE SAFETY GOGGLES (Head Protection)
Wear Safety goggles (must comply with ANS! a
2
)r other
carefully
for
of moving
and any
.A
Loading ...
Loading ...
Loading ...