Loading ...
Loading ...
Loading ...
7
It is important that the appliance steams without interruption for
20 minutes at 100 °C. Do not open the appliance door during
this time.
If the appliance was not able to calibrate itself automatically (for
example, because the appliance door was opened), the
calibration process is carried out again during the next cooking
operation.
After moving house
So that the appliance automatically adjusts itself to its new
location, you must reset the appliance to the factory settings
(see section: Basic settings) and repeat the initial start-up
process (see section: First use).
After a power cut
The appliance saves the calibration settings even in the event
of a power cut or disconnection from the mains. Recalibration
is not necessary.
Before using for the first time
In this section you will find out which steps are required before
using the appliance for the first time:
■ Setting the clock
■ Setting the water hardness range
■ Starting the appliance for the first time
■ Cleaning the accessories before use
Setting the clock
Note: When you press the KJ clock function button, you have
3 seconds to set the clock using the rotary selector. Should this
have been insufficient for you, you can amend the clock time
later.
‹:‹‹ flashes in the clock display.
1. Briefly press the KJ clock function button to go to the
setting mode.
The
KJ and 3 symbols light up. ‚ƒ:‹‹ appears in the
clock display.
2. Set the current time using the rotary selector.
Your setting is accepted after 3 seconds.
Changing the clock
To subsequently change the time, press the
KJclock function
button repeatedly until the
KJ and 3 symbols light up again.
Change the time with the rotary selector.
Setting the water hardness range
Caution!
The appliance may become damaged due to the use of
unsuitable liquids.
Do not use distilled water, highly chlorinated tap water
(> 40 mg/l) or other liquids.
Only use cold, fresh tap water, softened water or uncarbonated
mineral water.
The water hardness "medium" (
™†ƒ) is the default setting.
Change the value if your water is softer or harder.
You can check the water hardness with the test strips supplied
or ask your water supplier.
Notes
■ If your water is very hard, we recommend that you use
softened water.
■ If you use only softened water, you can set your appliance to
the "softened" water hardness range.
■ If you use mineral water, set the water hardness to hard.
■ If you use mineral water, you must only use non-carbonated
mineral water (see section "Filling and emptying the water
tank").
You can change the water hardness range in the basic settings
when the appliance is switched on.
1. If required, turn the operating mode selector to the Û position.
2. Press and hold the ± information button until ™‚ ‹ appears
in the temperature display.
3. Briefly press the ± information button repeatedly until ™†ƒ
appears in the temperature display (water
hardness "medium").
4. Use the temperature selector to set the water hardness.
5. Press and hold the ± info button for 3 seconds.
Your setting is saved.
First use
Before first use, heat the empty appliance with é Steam
cooking for 20 minutes at 100 °C. Do not open the appliance
door during this time. The appliance is automatically calibrated
(see section: Automatic calibration).
1. Press the operating mode selector so that it pops out.
The appliance switches on.
2. Fill and insert the water tank (see section: Filling the water
tank).
Before using for the first time, moisten the seal in the tank
cover with a little water.
3. Turn the operating mode selector round to é Steam
cooking.
4. Press the Start button.
The appliance heats up to 100 °C. The cooking time
(20 minutes) does not start to count down until the set
temperature has been reached. Do not open the appliance
door during this time.
The cooking operation ends automatically and an audible
signal sounds.
Water hardness Setting symbol (temperature dis-
play)
softened
™†‹
soft
™†‚
medium
™†ƒ
hard
™†„
very hard
™†…
Loading ...
Loading ...
Loading ...