Loading ...
Loading ...
Loading ...
4
EN
After connecting the appliance to the power supply for the rst time,
the display will guide you to set up the appliance for rst use.
1. The language selection
To select preferred language please
press button „<” or „>”.
Conrm by pressing „OK” button.
After language conrmation, the appliance will go through the rst
time use conguration menu.
2. Setting the water hardness
The water hardness is by default
set to level 3. To change water
hardness level press button „<” or „>”
repeatedly.
To conrm your choice press „OK”
button. The level must be set
according to the table below.
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in your
house. This information can be obtained from your local water supplier.
3. Filling the water softener
When water hardness is set, it is
required to ll water softener with
water and special regeneration salt.
Remove the lower rack and unscrew
the reservoir cap (anticlockwise)
As a rst step it is needed to ll
reservoir with water ( ~1.5 litres).
Once done, proceed to the next
step by pressing „OK” button.
Position the funnel (see gure) and ll the salt reservoir right up to its
edge (approximately 1 kg); it is not unusual for some water will spill out.
Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can get
into the container during the wash program (this could damage the
water softener beyond repair).
Once done, proceed to the next step by pressing „OK” button.
Only use salt that has been specically designed for dishwashers.
4. Setting the brightness level
The brightness level is by default set
to level 5. To change brightness level
press button „<” or „>” repeatedly.
To conrm Uour choice press „OK”
button.
5. Detergent type operation
In this step it is very important to
choose what type of detergent will
be used (tablet/capsule or
gel/powder).
If you prefer to use All-in-one
detergent in tablet or capsule for
washing - press „OK”, then go to
step 7. Open tap operation on the
next page.
The symbol on display will be lit. If you prefer to use gel or
powder detergent for washing, press „<” or „>”, then go to step 6.
Rinse aid operation.
6. Rinse aid operation*
*If All-in-one detergent was chosen in the previous step, this step will
be skipped by the appliance.
LANGUAGE: ENGLISH?
<> = CHANGE OK = YES
ENGLISH
SELECTED
WATER HARDNESS = 3
<> = CHANGE OK = YES
WATER HARDNESS
(1=MIN, 5=MAX)
POUR WATER
OPERATION
INSERT 1,5 LITER OF
OK = DONE
WATER IN THE
OK = DONE
WATER SOFTENER
OK = DONE
INSERT SALT
OPERATION
ADD 1KG OF SALT
OK = DONE
IN THE SALT DISPENSER
OK = DONE
ADJUST BRIGHTNESS
(1=MIN, 5=MAX)
BRIGHTNESS = 5
<> = CHANGE OK = YES
DETERGENT TYPE
OPERATION
DO YOU USE
<> = NO OK = YES
DETERGENT?
<> = NO OK = YES
“ALL IN ONE”
<> = NO OK = YES
RINSE AID
OPERATION
INSERT RINSE AID
OK = DONE
IN THE DISPENSER
OK = DONE
M
A
X
A
B
35
25
Water Hardness Table
Level
German
degrees °dH
French
degrees °fH
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 18 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
FIRST TIME USE
Whenever you need to add salt, it is mandatory to complete
theprocedure before the beginning of the washing cycle.
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
If the salt container is not lled, the water softener and the
heating element may be damaged as a result.
Loading ...
Loading ...
Loading ...